NFW31SP507X1E4L Datasheet NFW31SP507X1E4L, NFW31SP157X1E4L, NFW31SP506X1E4L | P1-P3

Spec. No. JENF243E-0009J-01 P1/ 10

MURATA MFG. CO., LTD.

Reference Only

Chip EMIFIL

for Signal Line

NFW31SP

□□□X1E4L Reference Specification

1. Scope

This reference specification applies to Chip EMIFIL® for signal line NFW31S series.

2. Part Numbering

NF W 31 SP 106 X 1E 4 L

Product ID Structure Dimension Features Cut-off Characteristics Rated Electrode Packaging Code

(L × W) Frequency Voltage [L: Taping]

3. Rating

3-1. Common Rating

Rated Voltage 25 V(DC)

Withstanding Voltage 62.5 V(DC)

Rated Current 200 mA

Insulation Resistance 1000 MΩ min.

Line Impedance 50 Ω

3-2. Individual Rating ∗ 6dB max.

Customer

Part Number

MURATA

Part Number

Insertion Loss (dB min.)

MHz

100

MHz

150

MHz

200

MHz

300

MHz

400

MHz

500

MHz

GHz

NFW31SP106X1E4L ∗ 5 25 25 - 25 - - 30 30

NFW31SP206X1E4L - ∗ 5 25 - 25 - - 30 30

NFW31SP506X1E4L - - ∗ 10 - 30 - - 30 30

NFW31SP107X1E4L - - - ∗ - 5 - - 20 30

NFW31SP157X1E4L - - - - ∗ - 10 20 30 30

NFW31SP207X1E4L - - - - - ∗ - - 10 30

NFW31SP307X1E4L - - - - - - ∗ - 5 15

NFW31SP407X1E4L - - - - - - - ∗ - 10

NFW31SP507X1E4L - - - - - - - - ∗ 10

• Operating Temperature : -40 to +85 °C • Storage Temperature : -55 to +85 °C

4. Standard Testing Condition

< Unless otherwise specified > <In case of doubt >

Temperature: Ordinary Temp 15 °C to 35 °C Temperature: 20 °C ± 2 °C

Humidity: Ordinary Humidity

25 %(RH) to 85 %(RH) Humidity: 60 %(RH) to 70 %(RH)

Atmospheric pressure: 86 kPa to 106kPa

5. Style and Dimensions

■ Equivalent Circuit

(1) Input (Output) Terminal

(2) Ground Terminal

(3) Output (Input) Terminal

• No polarity.

■ Unit Mass(Typical value)

0.030g

0.7±0.3

0.65±0.2

0.7±0.3

3.2±0.3

2.3±0.2

1.6±0.2

(1)

(2)

(3)

(in mm)

1.6±0.2

: Electrode

1.8±0.2

(1)

(

)

(

)

Spec. No. JENF243E-0009J-01 P2/ 10

MURATA MFG. CO., LTD.

Reference Only

■ Insertion Loss Characteristics (I.L.) (Typ.) (50Ωsystem)

6. Marking

No Marking

7. Electrical Performance

No. Item Specification Test Method

7.1 Insulation

Resistance(I.R.)

Meet item 3. DC rated voltage : 25 V

(Between input (or output) terminal and ground

terminal.)

The charge time : 60 ± 5 seconds

(Through the protect resistance of 1MΩ)

7.2 Withstanding

Voltage

No damage. DC rated voltage : 62.5 V

(Between input (or output) terminal

and ground terminal.)

Testing Time : 1 to 5 seconds

Limit the charging current: 10 mA max.

7.3 Insertion Loss

Characteristics

(I.L.)

Meet item 3. Measured by the following circuit (Fig 1. Table 1)

Table 1

Cable, Connector and

Measuring Condition

Line

Impedance

Impedance of Cable : 50Ω

Impedance of connector : 50Ω

· I.L. shall be measured after

connecting signal terminals T1,

T2 to (1), (2) in Fig.1 respectively.

50Ω

NETWORK ANALYZER

OUTPUT(50

)

∗

(1)

(2)

R- I N PU T ( 5 0

)

T- I N PU T ( 5 0

)

∗

1 Connect to terminals

of network analyzer

Fig.1

Network Analyzer:MS620J(ANRITSU) or the equivalent

Spec. No. JENF243E-0009J-01 P3/ 10

MURATA MFG. CO., LTD.

Reference Only

8. Mechanical Performance

No. Item Specification Test Method

8.1 Appearance and

Dimensions

Meet item 5. Visual Inspection and measured with Slide Calipers.

8.2 Bonding

Strength

Products shall be no failure after

tested.

It shall be soldered on the substrate.

Applying Force(F) : 4.9 N

Applying Time: 5 ± 1 s

8.3 Solderability The electrodes shall be at least 90%

covered with new solder coating.

Flux : Ethanol solution of rosin,25 (wt)%

Pre-heat : 150 ± 10 °C, 60 to 90 s

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 240 ± 3 °C

Immersion Time : 3 ± 1 s

Immersion and emersion rates : 25 mm / s

8.4 Resistance to

soldering heat

Meet Table 2.

Table 2

Flux: Ethanol solution of rosin, 25(wt)%

Pre-heat: 150 ± 10 °C, 60 to 90 s

Solder: Sn-3.0Ag-0.5Cu

Solder Temperature: 270 ± 5 °C

Immersion Time: 10 ± 1 seconds

Immersion and emersion rates : 25 mm / s

Then measured after exposure in the room

condition for 4 to 48 hours.

Initial values : Then measured after heat treatment

(150°C (+0°C,-10°C), 1 hour) and exposure in

the room condition for 4 to 48 hours.

8.5 Bending

Strength

Products shall be no failure after

tested.

It shall be soldered on the Glass-epoxy substrate.

(100 × 40 × 1.6 (mm))

(in mm)

Deflection : 2.0 mm

(for NFW31SP106/206 : 1.0 mm)

Keeping Time : 10 seconds

Speed of Applying Force : 1.0 mm / s

8.6 Vibration Meet table 3.

Table 3

It shall be soldered on the substrate.

Oscillation Frequency : 10 to 55 to 10Hz for

1 minute

Double Amplitude : 1.5 mm

Testing Time : A period of 2 hours in each of 3

Mutually perpendicular directions.

(Total 6 hours)

Pattern

Substrate

Products

(in mm)

1.0

0.6

2.2

Appearance No damage.

Withstanding

Voltage

No damage.

I.R.

Meet item 3.

I.L.

Appearance No damage

Withstanding

Voltage

No damage

I.R.

100MΩ min.

I.L. Meet item 3.

R340

Deflection

Product

Pressure jig

P1-P3 P4-P6 P7-P9 P10-P10

NFW31SP507X1E4L

Mfr. #:

Buy NFW31SP507X1E4L

Manufacturer:

Murata Electronics

Description:

EMI Filter Circuits 500MHZ C/O 25V 0.2A

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

NFW31SP507X1E4L

NFW31SP507X1E4L

Products related to this Datasheet