JGN1105H-TR Datasheet JGN1105H-TR | P10-P12

JGN1105H-TR Soldering condition

4. If soldering manually, Stanley recommends using a soldering iron equipped with temperature control. During

the actual soldering process, make sure that the soldering iron never touch the LED itself, and avoid the LED's

electrode heating temperature reaching above the heating temperature of the solder pad. All repairs must be

performed only once in the same spot, and please avoid reusing components.

5. In soldering process, immediately after iron tip is cleaned, please make sure that the soldering iron reaches the

appropriate temperature before using. Also, please avoid applying any type of pressure to the soldered

components before the solder has been cooled and hardened, as it may deteriorate solder performance and

solder quality.

6. When using adhesive material for tentative fixatives, thermosetting resin or Ultraviolet radiation (UV)

setting resin with heat shall be recommended.

《The curing condition, Temperature:150℃Max./Time:120sec.Max.》

7. Flow soldering (dip soldering) is not recommended for this product.

8. lsopropyl alcohol is recommended for cleaning. Some chemicals, including Freon substitute detergent could

corrode the lens or the casing surface, which cause discoloration, cloud, crack and so on. Please review the

reference chart below for cleaning. If water is used to clean (including the final cleaning process), please use

pure water (not tap water), and completely dry the component before using.

【Recommended Manual Soldering Condition】

Temperature of Iron Tip

350℃MAX.

Soldering Duration, Time 3sec.Max.,1 time

Page : 10

Chemical

○／×

Isopropyl Alcohol

○

Ethyl

Alcohol

○

Pure water

○

Trichloroethylene

Chlorothene

Acetone

Thinner

9. When using Freon equivalent solvent, discoloration on the LED surface may be caused by one of the first

confirming that there is no problem.

Freon substitute detergent

・Clean through-750H

・Pine alpha ST-100S

10. In the case of water-washing, ensure to use pure water (not city water) and immediately after washing is over,

apply forced drying to removed all moisture from the LED.

2016.11.28

JGN1105H-TR

・Adsorption nozzle for picking up

＜Recommendation＞

Handling Precaution

【Handling Precautions for Product Mounting】

Page : 11

When use the adsorption nozzle, its inner diameter should be φ1.7mm to φ1.8mm

because of lens shape of LED.

2016.11.28

JGN1105H-TR

1. Stanley LED Lamps have semiconductor characteristics and are designed to ensure high reliability. However,

the performance may vary depending on usage conditions

2. Absolute Maximum Ratings are set to prevent LED lamps from failing due to excess stress( temperature,

current, voltage, etc.). Usage conditions must not exceed the ratings for a moment, nor do reach one item of

absolute maximum ratings simultaneously.

3. In order to ensure high reliability from LED Lamps, variable factors that arise in actual usage conditions

should be taken into account for designing. ( Derating of TYP., MAX Forward Voltage, etc.)

4. Please insert Protective Resistors into the circuit in order to stabilize LED operation and to prevent the device

from igniting due to excess current.

5. Please check the actual performance in the assembly because the Specification Sheets are described for LED

device only.

6. Please refrain from looking directly at the light source of LED at high output, as it may harm your vision.

7. The products are designed to operate without failure in recommended usage conditions. However, please take

the necessary precautions to prevent fire, injury, and other damages should any malfunction or failure arise.

8. The products are manufactured to be used for ordinary electronic equipment. Please contact our sales staff

beforehand when exceptional quality and reliability are required, and the failure or malfunction of the

products might directly jeopardize life or health ( such as for airplanes, aerospace, transport equipment,

medical applications, nuclear reactor control systems and so on).

9. When there is a process of supersonic wave welding etc. after mounting the product, there is a possibility of

affecting on the reliability of junction part in package (junction part of die bonding and wire bonding). Please

make sure there is no problem before using.

10. The formal specification sheets shall be valid only by exchange of documents signed by both parties.

Handling Precaution

【Other Precautions】

Page : 12

2016.11.28

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15 P16-P18 P19-P21 P22-P23

JGN1105H-TR

Mfr. #:

Buy JGN1105H-TR

Manufacturer:

Description:

RoHS(ship within 1day)

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

JGN1105H-TR