www.fairchildsemi.com 4
74LVTH16835
DC Electrical Characteristics
Note 5: An external driver must source at least the specified current to switch from LOW-to-HIGH.
Note 6: An external driver must sink at least the specified current to switch from HIGH-to-LOW.
Note 7: This is the increase in supply current for each input that is at the specified voltage level rather than V
CC
or GND.
Dynamic Switching Characteristics (Note 8)
Note 8: Characterized in SSOP package. Guaranteed parameter, but not tested.
Note 9: Max number of outputs defined as (n). n−1 data inputs are driven 0V to 3V. Output under test held LOW.
Symbol Parameter
V
CC
T
A
= −40°C to +85°C
Units Conditions
(V) Min Max
V
IK
Input Clamp Diode Voltage 2.7 −1.2 V I
I
= −18 mA
V
IH
Input HIGH Voltage 2.7–3.6 2.0
V
V
O
≤ 0.1V or
V
IL
Input LOW Voltage 2.7–3.6 0.8 V
O
≥ V
CC
− 0.1V
V
OH
Output HIGH Voltage 2.7–3.6 V
CC
− 0.2 V I
OH
= −100 µA
2.7 2.4 V I
OH
= −8 mA
3.0 2.0 V I
OH
= −32 mA
V
OL
Output LOW Voltage 2.7 0.2 V I
OL
= 100 µA
2.7 0.5 V I
OL
= 24 mA
3.0 0.4 V I
OL
= 16 mA
3.0 0.5 V I
OL
= 32 mA
3.0 0.55 V I
OL
= 64 mA
I
I(HOLD)
Bushold Input Minimum Drive
3.0
75 µAV
I
= 0.8V
−75 µAV
I
= 2.0V
I
I(OD)
Bushold Input Over-Drive
3.0
500 µA(Note 5)
Current to Change State −500 µA(Note 6)
I
I
Input Current 3.6 10 µAV
I
= 5.5V
Control Pins 3.6 ±1 µAV
I
= 0V or V
CC
Data Pins 3.6
−5 µAV
I
= 0V
1 µAV
I
= V
CC
I
OFF
Power Off Leakage Current 0 ±100 µA0V ≤ V
I
or V
O
≤ 5.5V
I
PU/PD
Power Up/Down 3-STATE
0–1.5V ±100 µA
V
O
= 0.5V to 3.0V
Output Current V
I
= GND or V
CC
I
OZL
3-STATE Output Leakage Current 3.6 −5 µAV
O
= 0.5V
I
OZH
3-STATE Output Leakage Current 3.6 5 µAV
O
= 3.0V
I
OZH
+ 3-STATE Output Leakage Current 3.6 10 µAV
CC
< V
O
≤ 5.5V
I
CCH
Power Supply Current 3.6 0.19 mA Outputs HIGH
I
CCL
Power Supply Current 3.6 5 mA Outputs LOW
I
CCZ
Power Supply Current 3.6 0.19 mA Outputs Disabled
I
CCZ
+ Power Supply Current 3.6 0.19 mA V
CC
≤ V
O
≤ 5.5V,
Outputs Disabled
∆I
CC
Increase in Power Supply Current 3.6 0.2 mA One Input at V
CC
− 0.6V
(Note 7) Other Inputs at V
CC
or GND
Symbol Parameter
V
CC
T
A
= 25°C
Units
Conditions
(V) Min Typ Max
C
L
= 50 pF, R
L
= 500Ω
V
OLP
Quiet Output Maximum Dynamic V
OL
3.3 0.8 V (Note 9)
V
OLV
Quiet Output Minimum Dynamic V
OL
3.3 −0.8 V (Note 9)
