OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TB6562AFG,8,EL

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18
TB6562ANG/AFG
< TB6562AFG >
Pin No. Symbol Function Description Remarks
1 GND Ground pin
2 V
reg
5 V output pin Connect a capacitor between this pin and the GND pin.
3 SB Standby pin
H: start, L: Standby, Built-in pull down resistance of
100 kΩ (typ.)
4 Phase A Rotation direction control pin (Ch. A)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
5 X1A Input pin used to set output current level (Ch. A)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
6 X2A Input pin used to set output current level (Ch. A)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
7 GND Ground pin
8 GND Ground pin
9 GND Ground pin
10 V
CC
Power supply voltage input pin V
CC (opr)
= 10 V to 34 V
11 OUT1A Output pin 1 (Ch. A) Connect to a motor coil pin.
12 V
ref
A Reference voltage external set pin (Ch. A)
13 RSA Resistance connect pin for detecting output current (Ch. A)
14 OUT2A Output pin 2 (Ch. A) Connect to a motor coil pin.
15 GND Ground pin
16 GND Ground pin
17 OUT2B Output pin 2 (Ch. B) Connect to a motor coil pin.
18 RSB Output current detection resistor connection pin (Ch. B)
19 V
ref
B Input pin for external reference voltage (Ch. B)
20 OUT1B Output pin 1 (Ch. B) Connect to a motor coil pin.
21 V
CC
Power supply voltage input pin V
CC (opr)
= 10 V to 34 V
22 GND Ground pin
23 GND Ground pin
24 GND Ground pin
25 X2B Input pin used to set output current level (Ch. B)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
26 X1B Input pin used to set output current level (Ch. B)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
27 Phase B Rotation direction control pin (Ch. B)
Apply a 0 V/5 V signal, Built-in pull down resistance
of 100 kΩ (typ.)
28 OSC External capacitor pin for triangular-wave oscillation
29 V
CC
Power supply voltage input pin V
CC (opr)
= 10 V to 34 V
30 GND Ground pin
2012-09-28
4
TB6562ANG/AFG
Absolute Maximum Ratings
(T
a
= 25°C)
Characteristic Symbol Rating Unit
Power supply voltage V
CC
40 V
Output voltage V
O
40 V
Output current I
O (Peak)
1.5 (Note 1) A
Input voltage V
IN
−0.2 to 5.5 V
Power dissipation P
D
2.5 (Note 2) W
Operating temperature T
opr
−20 to 85 °C
Storage temperature T
stg
−55 to 150 °C
Junction temperature T
j
max 150 °C
Note 1: Output current may be controlled by excitation mode, ambient temperature, or heatsink.
When designing a circuit, ensure that the maximum junction temperature, T
j
max = 150°C, is not exceeded
when the IC is used.
Avoid using the IC in abnormal conditions that would cause the T
j
to exceed 150°C, even though the heat
protection circuit of the IC will continue to operate in such conditions.
Note 2: When mounted on a board (50 mm × 50 mm × 1.6 mm, Cu area: 50%)
The absolute maximum ratings of a semiconductor device are a set of ratings that must not be exceeded, even for a
moment. Do not exceed any of these ratings.
Exceeding the rating (s) may cause the device breakdown, damage or deterioration, and may result injury by explosion
or combustion.
Please use the IC within the specified operating ranges.
Operating Range
(T
a
= –20 to 85°C)
Characteristic Symbol Rating Unit
Power supply voltage V
CC
10 to 34 V
Input voltage V
IN
0 to 5 V
Vref voltage V
ref
0.5 to 7.0 V
PWM frequency f
pwm
15 to 80 kHz
Triangular-wave oscillation frequency f
OSC
45 to 400 kHz
2012-09-28
5
TB6562ANG/AFG
Electrical Characteristics
(V
CC
= 24 V, T
a
= 25°C)
Characteristic Symbol
Test
Circuit
Test Condition Min Typ. Max Unit
I
CC1
XT1A = XT2A = H, XT1B = XT2B = H
Output = Open
― 6.5 10
I
CC2
XT1A = XT2A = L, XT1B = XT2B = L
Output = Open
― 7.0 12
Supply current
I
CC3
―
Standby mode ― 2.0 4.0
mA
V
INH
― 2.3 ― 5.5
Input voltage
V
INL
―
― -0.2 ― 0.8
Input hysteresis
voltage
V
IN (HYS)
― (Target spec.) ― 0.4 ―
V
I
INH
V
IN
= 5 V 30 50 75
Control circuit
(Note 1)
Input current
I
INL
―
V
IN
= 0 V ― ― 5
μA
V
INSH
― 2.3 ― 5.5
Input voltage
V
INSL
―
― –0.2 ― 0.8
Input hysteresis
voltage
V
IN (HYS)
― (Target spec.) ― 0.4 ―
V
I
INSH
V
IN
= 5 V 30 50 75
Standby circuit
Input current
I
INSL
―
V
IN
= 0 V ― ― 5
μA
I
O
= 0.2 A ― 1.5 2.0
Output ON-resistance R
on (U+L)
―
I
O
= 1.5 A ― 1.5 2.0
Ω
I
L (U)
V
CC
= 40 V ― ― 10
Output leakage current
I
L (L)
―
V
CC
= 40 V ― ― 10
μA
V
F (U)
I
O
= 1.5 A ― 1.3 2.0
Diode forward voltage
V
F (L)
―
I
O
= 1.5 A ― 1.3 2.0
V
Internal reference voltage V
reg
― When current of 1 mA is loaded. 4.75 5 5.25 V
Input current I
ref
― V
ref
= 0.5 V ― 5 10 μA
V
ref
(1/10) ―
X1 = X2 = L
V
ref
= 5 V
0.45
0.5
0.55
V
ref
(1/15) ―
X1 = L, X2 = H
V
ref
= 5 V
0.28
0.33
0.38
Vref circuit
Current limit
voltage
V
ref
(1/30) ―
X1 = H, X2 = L
V
ref
= 5 V
0.12
0.17
0.22
V
Triangular-wave oscillation
frequency
f
OSC
― C = 4700 pF 88 110 132 kHz
Thermal shutdown circuit operating
temperature
T
SD
―
(Target spec.)
― 160 ― °C
Note 1: Phase, X1 and X2 pins
2012-09-28
6
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18

TB6562AFG,8,EL

Mfr. #:
Buy TB6562AFG,8,EL
Manufacturer:
Description:
Motor / Motion / Ignition Controllers & Drivers Stepping Motor Driver IC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet