2
Precision Edge
®
SY89544U
Micrel, Inc.
M9999-082407
hbwhelp@micrel.com or (408) 955-1690
Pin Number Pin Name Pin Function
4, 2, 32, IN0, /IN0, Differential Inputs: These input pairs are the differential signal inputs to the device. Inputs
30, 27, 25, 23, 21 IN1, /IN1, accept AC- or DC-coupled signals as small as 100mV. Each pin of a pair internally
IN2, /IN2, terminates to a V
T
pin through 50Ω. Note that these inputs will default to an indeterminate
IN3, /IN3 state if left open. Unused differential input pairs can be terminated by connecting one input
to V
CC
and the complementary input to GND through a 1kΩ resistor. The V
T
pin is to be
left open in this configuration. Please refer to the “Input Interface Applications” section for
more details.
3, 31, 26, 22 VT0, VT1, Input Termination Center-Tap: Each side of the differential input pair, terminates to a V
T
VT2, VT3 pin. The V
T0
, V
T1
, V
T2
, V
T3
pins provide a center-tap to a termination network for
maximum interface flexibility. See “Input Interface Applications” section for more details.
6, 19 SEL0, SEL1 These single-ended TTL/CMOS compatible inputs select the inputs to the multiplexers.
Note that these inputs are internally connected to a 25kΩ pull-up resistor and will default
to a logic HIGH state if left open. Input switching threshold is V
CC
/2.
1, 5, 8, VCC Positive Power Supply: Bypass with 0.1µF||0.01µF low ESR capacitors. The 0.01µF
17, 20, 24, 28, 29 capacitor should be as close to a V
CC
pin as possible.
10, 11 Q, /Q Differential Outputs: This LVDS output pair is the output of the device. It is a
logic function of the IN0, IN1, IN0, IN1 and SEL0 inputs. Please refer to the “Truth Table’”
for details.
7, 9, 12, 13, 16, 18 GND, Ground: Ground pin and exposed pad must be connected to the same ground plane.
Exposed pad
14, 15 NC No connect (unused pins).
PIN DESCRIPTION
PACKAGE/ORDERING INFORMATION
24
23
22
21
20
19
18
17
VCC
IN3
VT3
/IN3
VCC
SEL1
GND
VCC
VCC
/IN0
VT0
/IN0
VCC
SEL0
GND
VCC
1
2
3
4
5
6
7
8
910111213141516
32 31 30 29 28 27 26 25
VCC
VCC
/IN1
VT1
IN1
IN2
VT2
/IN2
GND
GND
/Q
Q
GND
NC
NC
GND
32-Pin MLF
®
Ordering Information
(1)
Package Operating Package Lead
Part Number Type Range Marking Finish
SY89544UMI MLF-32 Industrial SY89544U Sn-Pb
SY89544UMITR
(2)
MLF-32 Industrial SY89544U Sn-Pb
SY89544UMG
(3)
MLF-32 Industrial SY89544U with Pb-Free
Pb-Free bar-line indicator NiPdAu
SY89544UMGTR
(2, 3)
MLF-32 Industrial SY89544U with Pb-Free
Pb-Free bar-line indicator NiPdAu
Notes:
1. Contact factory for die availability. Dice are guaranteed at T
A
= 25°C, DC electricals only.
2. Tape and Reel.
3. Recommended for new designs.