OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ISL4089IBZ

P1-P3P4-P6P7-P9
1
®
FN6192.1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2006. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
ISL4089
DC-Restored Video Amplifier
The ISL4089 is complete DC-restored monolithic video
amplifier sub-system. It contains a high performance video
amplifier and a nulling, sample-and-hold amplifier designed
to establish a programmable DC output level.
When the HOLD logic input “0” is applied the DC restore
function is active. The sample-and-hold amplifier loop is
closed and used to null the DC offset of the video amplifier.
This can occur during sync, or, at any time that a black level
is expected. When the HOLD input “1” is applied, the
correcting voltage is stored on the video amplifier’s input
coupling capacitor. This condition must be true during active
video. The restored DC voltage level can be adjusted using
an external reference voltage applied to the V
REF
pin.
The device operates from a single +5V supply and is ideal
for +5V only systems when used with a sync separator, such
as the EL1883.
The ISL4089 is intended to directly replace the EL4089 only
in certain applications. This direct replacement requires that
the single positive supply is no higher than +5.5V and that no
part of the clamped output goes below ground. The NC on
pin 6 is not internally connected, so it can be connected to
the -5V pin in existing EL4089 applications.
The ISL4089 is specified for operation over -40°C to +85°C
temperature range.
Pinout
ISL4089
(8 Ld SOIC)
TOP VIEW
Features
• Complete video level DC-restoration system
• 0.03% differential gain and 0.05° differential phase
accuracy
• 300MHz -3dB small signal bandwidth at A
V
= 1
• 150MHz -3dB small signal bandwidth at A
V
= 2
• 300V/µs Slew Rate
• 0.1dB flatness to 80MHz
• +5V single supply operation
• TTL/CMOS compatible hold signal
• Pb-free plus anneal available (RoHS compliant)
Applications
• Input amplifier in video equipment
• DC-restoration amplifier in video mixers
Related Documents
• AN1261: ISL4089EVAL1 User’s Guide
• AN1089: EL4089 and EL4390 DC-Restored Video
Amplifier
+
-
+
-
GND
N/C
V
OUT
V+
HOLD
V
REF
IN+
IN-
+
-
+
-
+
-
+
-
GND
N/C
V
OUT
V+
HOLD
V
REF
IN+
IN-
Ordering Information
PART NUMBER
PART
MARKING
TAPE &
REEL PACKAGE
PKG.
DWG. #
ISL4089IBZ
(See Note)
4089IBZ - 8 Ld SO
(Pb-free)
MDP0027
ISL4089IBZ-T7
(See Note)
4089IBZ 7” 8 Ld SO
(Pb-free)
MDP0027
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100%
matte tin plate termination finish, which are RoHS compliant and
compatible with both SnPb and Pb-free soldering operations. Intersil
Pb-free products are MSL classified at Pb-free peak reflow
temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
Data Sheet June 28, 2006
2
FN6192.1
June 28, 2006
Absolute Maximum Ratings (T
A
= 25°C)
Voltage between V+ and GND. . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Voltage between IN+, IN-, HOLD, V
REF
and GND
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND -0.5;V+ +0.5V
Supply Turn-on Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . 1V/µs
Digital and Analog Input Current (Note 1) . . . . . . . . . . . . . . . . 50mA
Output Current (Continuous) . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7). . . .3000V
Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250V
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . .-40°C to +125°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
DC Electrical Specifications V+ = +5V, Load = 1kΩ; T
A
= +25°C
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
AMPLIFIER SECTION (HOLD = 5V)
Ib+ IN+ Input Bias Current V
IN+
= 2.5V -7 20 µA
Ib- IN- Input Bias Current V
IN-
= 1.3V -30 -1 µA
A
VOL
Open Loop Gain 60 dB
V
OUT+
High Output Level R
L
= 1k 3.5 V
V
OUT-
Low Output Level IL = 0mA 5 mV
I
SC
Short Circuit Current 100 mA
RESTORE SECTION
V
OS
, Comp Composite Input Offset Voltage V
REF
= 0V to +2.5V 10 15 mV
I
OUT
Restoring Current Available 300 µA
PSRR Power Supply Rejection Ratio V+ = 5V to 6V 70 90 dB
Ib V
REF
V
REF
Input Bias Current V
REF
= +2.5V -0.8 -0.5 -0.2 µA
V
H
HOLD HOLD Logic Input Low 0.8 V
V
L
HOLD HOLD Logic Input High 2.0 V
I
IH
, Hold HOLD Input Current @ Logic High V
HOLD
= 5V -15 30 µA
I
IL
, Hold HOLD Input Current @ Logic Low V
HOLD
= 0V -5 5 µA
I
S
Supply Current V
HOLD
= 0V 17 20 23 mA
AC Electrical Specifications V
S
= +5V, V
REF
= 0V
DC
, R
L
= 150Ω, R
F
and R
G
= 475Ω; A
V
= 2, T
A
= +25°C.
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNITS
AMPLIFIER SECTION
SR Slew Rate; 2V
P-P
, 20% to 80% 300 V/µs
tr, tf Output Rise and Fall Times V
OUT
= 0.2Vp-p; 10% to 90% 3.2 ns
tpd Propagation Delay, IN+ to Output V
OUT
= 0.2V; 10% to 10% 0.3 ns
-3dB BW Small Signal; Unity Gain R
F
= 0; R
G
= inf.; C
L
= 0.6pF,
V
OUT
= 0.2V
P-P
300 MHz
Large Signal; Unity Gain R
F
= 0; R
G
= inf.; C
L
= 0.6pF,
V
OUT
= 2V
P-P
95 MHz
Small Signal; A
V
= +2 C
L
= 0.6pF, V
OUT
= 0.2V
P-P
150 MHz
Large Signal; A
V
= +2 C
L
= 0.6pF, V
OUT
= 2V
P-P
85 MHz
ISL4089
3
FN6192.1
June 28, 2006
0.1dB BW 0.1dB Gain Flatness; Unity Gain R
F
= 0; R
G
= inf.; C
L
= 0.6pF
V
OUT
= 0.2V
P-P
70 MHz
R
F
= 0; R
G
= inf.; C
L
= 0.6pF
V
OUT
= 2V
P-P
60 MHz
0.1dB Gain Flatness; A
V
= +2 C
L
= 0.6pF, V
OUT
= 0.2V
P-P
80 MHz
C
L
= 0.6pF, V
OUT
= 2V
P-P
50 MHz
dG Differential Gain Error NTC-7, Restore on sync tip 0.03 %
dP Differential Phase Error NTC-7, Restore on sync tip 0.05 °
RESTORE SECTION
T
HE
Time to Enable Hold; 50% to 50% HOLD input 0V to +5V 40 ns
T
HD
Time to Disable Hold; 50% to 50% HOLD input 5V to 0V 20 ns
NOTE:
1. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values
Typical Performance Curves V
S
= +5V, R
L
= 150Ω to GND, C
L
= 0.6pF, T
A
= 25°C, unless otherwise specified.
FIGURE 1. SMALL SIGNAL GAIN vs FREQUENCY for
VARIOUS GAINS
FIGURE 2. LARGE SIGNAL GAIN vs FREQUENCY for
VARIOUS GAINS
FIGURE 3. LARGE SIGNAL GAIN vs FREQUENCY vs C
L
FIGURE 4. SMALL SIGNAL GAIN vs R
F
, R
G
AC Electrical Specifications V
S
= +5V, V
REF
= 0V
DC
, R
L
= 150Ω, R
F
and R
G
= 475Ω; A
V
= 2, T
A
= +25°C. (Continued)
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNITS
-10
-8
-6
-4
-2
0
2
4
6
1M 10M 100M 500M
FREQUENCY (Hz)
NORMALIZED GAIN (dB)
8
10
V
OUT
= 0.2V
P-P
R
L
= 150Ω
A
V
= 2
R
F
= R
G
= 475Ω
R
F
= 0Ω
A
V
= 1
A
V
=4
R
F
= 475Ω
R
G
= 158Ω
-10
-8
-6
-4
-2
0
2
4
6
8
10
1M 10M 100M 500M
FREQUENCY (Hz)
NORMALIZED GAIN (dB)
V
OUT
= 2V
P-P
R
L
= 150Ω
A
V
= 4
R
F
= 475Ω
R
G
= 158Ω
A
V
= 1
R
F
= 0Ω
A
V
= 2
R
F
= R
G
= 475Ω
-10
-8
-6
-4
-2
0
2
4
6
8
10
1M 10M 100M 500M
FREQUENCY (Hz)
NORMALIZED GAIN (dB)
V
OUT
= 2V
P-P
R
L
= 150Ω
A
V
= 2
C
L
= 0.6pF
A
V
= 2
C
L
= 22pF
A
V
= 1
C
L
= 0.6pF to 22pF
-10
-8
-6
-4
-2
0
2
4
6
8
10
1M 10M 100M 500M
FREQUENCY (Hz)
NORMALIZED GAIN (dB)
R
F
= R
G
= 301Ω
V
OUT
= 0.2V
P-P
R
L
= 150Ω
AV = 2
R
F
= R
G
= 1kΩ
R
F
= R
G
= 475Ω
ISL4089
P1-P3P4-P6P7-P9

ISL4089IBZ

Mfr. #:
Buy ISL4089IBZ
Manufacturer:
Renesas / Intersil
Description:
Video Amplifiers ISL54105CRZ TMDS GENRTR W/MLTIPLEXR72
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet