OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HCPL-7520-300

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
4
Solder Reow Temperature Prole
Recommended Pb-Free IR Prole
0
TIME (SECONDS)
TEMPERATURE (˚C)
200
100
50 150100 200 250
300
0
30
SEC.
50 SEC.
30
SEC.
160˚C
140˚C
150˚C
PEAK
TEMP.
245˚C
PEAK
TEMP.
240˚C
PEAK
TEMP.
230˚C
SOLDERING
TIME
200˚C
PREHEATING TIME
150˚C, 90 + 30 SEC.
2.5˚C ± 0.5˚C/SEC.
3˚C + 1˚C/–0.5˚C
TIGHT
TYPICAL
LOOSE
ROOM TEMPERATURE
PREHEATING RATE 3˚C + 1˚C/–0.5˚C/SEC.
REFLOW HEATING RATE 2.5˚C ± 0.5˚C/SEC.
Note: Use of non-chlorine-activated uxes is highly recommended.
Note: Use of non-chlorine-activated uxes is highly recommended.
5
Regulatory Information
The HCPL-7520 has been approved by the following organizations:
Notes:
1. Insulation characteristics are guaranteed only within the safety
maximum ratings which must be ensured by protective circuits
within the application. Surface Mount Classications is Class A in
accordance with CECC00802.
2. Refer to the optocoupler section of the Isolation and Control
Components Designer’s Catalog, under Product Safety Regulations
section, (IEC/EN/DIN EN 60747-5-2) for a detailed description of
Method a and Method b partial discharge test proles.
3. Refer to the following gure for dependence of P
S
and I
S
on ambient
temperature.
UL
Approved under UL 1577, component recognition
program up to V
ISO
= 3750 V
RMS
. File E55361.
CSA
Approved under CSA Component Acceptance
Notice #5, File CA 88324.
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01.
OUTPUT POWER – P
S
, INPUT CURRENT – I
S
0
0
T
S
– CASE TEMPERATURE – °C
200
600
400
25
800
50 75 100
200
150 175
P
S
(mW)
125
100
300
500
700
I
S
(mA)
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics
[1]
Description Symbol Characteristic Unit
Installation classication per DIN EN 0110-1/1997-04, Table 1
for rated mains voltage ≤ 150 V
rms
I – IV
for rated mains voltage ≤ 300 V
rms
I – III
for rated mains voltage ≤ 600 V
rms
I – II
Climatic Classication 55/100/21
Pollution Degree (DIN EN 0110-1/1997-04) 2
Maximum Working Insulation Voltage V
IORM
891 V
peak
Input to Output Test Voltage, Method b
[2]
V
IORM
x 1.875 = V
PR
, 100% production test with t
m
= 1 sec, partial discharge <5 pC V
PR
1670 V
peak
Input to Output Test Voltage, Method a
[2]
V
IORM
x 1.5 = V
PR
, type and sample test, t
m
= 60 sec, partial discharge <5 pC V
PR
1336 V
peak
Highest Allowable Overvoltage (transient overvoltage t
ini
= 10 sec) V
IOTM
6000 V
peak
Safety-limiting values – maximum values allowed in the event of a failure.
Case Temperature T
S
175 °C
Input Current
[3]
I
S, INPUT
400 mA
Output Power
[3]
P
S, OUTPUT
600 mW
Insulation Resistance at T
S
, V
IO
= 500 V R
S
>10
9
Ω
6
Insulation and Safety Related Specications
Parameter Symbol Value Unit Conditions
Minimum External Air Gap L(101) 7.4 mm Measured from input terminals to output terminals,
(clearance) shortest distance through air.
Minimum External Tracking L(102) 8.0 mm Measured from input terminals to output terminals,
(creepage) shortest distance path along body.
Minimum Internal Plastic Gap 0.5 mm Through insulation distance conductor to conductor,
(internal clearance) usually the straight line distance thickness between
the emitter and detector.
Tracking Resistance CTI >175 V DIN IEC 112 Part 1
(comparative tracking index)
Isolation Group IIIa Material Group (DIN EN 0110-1/1997-04)
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Note
Storage Temperature T
S
–55 125 °C
Operating Temperature T
A
–40 100 °C
Supply Voltage V
DD1
, V
DD2
0 6 V
Steady-State Input Voltage V
IN+
, V
IN-
–2.0 V
DD1
+ 0.5 V
Two Second Transient Input Voltage V
IN+
, V
IN-
–6.0 V
DD1
+ 0.5 V
Output Voltage V
OUT
–0.5 V
DD2
+ 0.5 V
Reference Input Voltage V
REF
0.0 V
DD2
+ 0.5 V
Reference Input Current I
REF
20 mA
Lead Solder Temperature 260°C for 10 sec., 1.6 mm below seating plane
Solder Reow Temperature Prole See Package Outline Drawings section
Recommended Operating Conditions
Parameter Symbol Min. Max. Units Note
Operating Temperature T
A
–40 85 °C
Supply Voltage V
DD1
, V
DD2
4.5 5.5 V
Input Voltage (accurate and linear) V
IN+
, V
IN-
–200 200 mV
Input Voltage (functional) V
IN+
, V
IN-
–2.0 2.0 V
Reference Input Voltage V
REF
4.0 V
DD2
V
Option 300 - surface mount classication is Class A in accordance with CECC 00802.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

HCPL-7520-300

Mfr. #:
Buy HCPL-7520-300
Manufacturer:
Broadcom / Avago
Description:
Optically Isolated Amplifiers 4.5 - 5.5 SV +/-5%
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet