LTC3851A-1
18
3851a1fa
applicaTions inForMaTion
is low. When the topside MOSFET is to be turned on, the
driver places the C
B
voltage across the gate source of the
MOSFET. This enhances the MOSFET and turns on the
topside switch. The switch node voltage, SW, rises to V
IN
and the BOOST pin follows. With the topside MOSFET on,
the boost voltage is above the input supply:
V
BOOST
= V
IN
+ V
INTVCC
The value of the boost capacitor, C
B
, needs to be 100 times
that of the total input capa citance of the topside MOSFET.
The reverse break down of the external Schottky diode
must be greater than V
IN(MAX)
.
Undervoltage Lockout
The LTC3851A-1 has two functions that help protect the
controller in case of undervoltage conditions. A precision
UVLO comparator constantly monitors the INTV
CC
voltage
to ensure that an adequate gate-drive voltage is present.
It locks out the switching action when INTV
CC
is below
3.2V. To prevent oscillation when there is a disturbance
on the INTV
CC
, the UVLO comparator has 400mV of preci-
sion hysteresis.
Another way to detect an undervoltage condition is to moni-
tor the V
IN
supply. Because the RUN pin has a precision
turn-on reference of 1.22V, one can use a resistor divider
to V
IN
to turn on the IC when V
IN
is high enough.
C
IN
Selection
In continuous mode, the source current of the top N-chan-
nel MOSFET is a square wave of duty cycle V
OUT
/V
IN
. To
prevent large voltage transients, a low ESR input capacitor
sized for the maximum RMS current must be used. The
maximum RMS capacitor current is given by:
I
RMS
≅ I
O(MAX)
V
OUT
V
IN
V
IN
V
OUT
– 1
⎛
⎝
⎜
⎞
⎠
⎟
1/2
This formula has a maximum at V
IN
= 2V
OUT
, where I
RMS
=
I
O(MAX)
/2. This simple worst-case condition is com monly
used for design because even significant deviations do not
offer much relief. Note that capacitor manufacturers’ ripple
current ratings are often based on only 2000 hours of life.
This makes it advisable to further derate the capacitor or
to choose a capacitor rated at a higher temperature than
required. Several capacitors may also be paralleled to meet
size or height requirements in the design. Always consult
the manufacturer if there is any question.
C
OUT
Selection
The selection of C
OUT
is primarily determined by the effec-
tive series resistance, ESR, to minimize voltage ripple. The
output ripple, ∆V
OUT
, in continuous mode is determined by:
∆V
OUT
≈ ∆I
L
ESR +
1
8fC
OUT
⎛
⎝
⎜
⎞
⎠
⎟
where f = operating frequency, C
OUT
= output capaci tance
and ∆I
L
= ripple current in the inductor. The output ripple
is highest at maximum input voltage since ∆I
L
increases
with input voltage. Typically, once the ESR requirement
for C
OUT
has been met, the RMS current rating gener-
ally far exceeds the I
RIPPLE(P-P)
requirement. With ∆I
L
=
0.3I
OUT(MAX)
and allowing 2/3 of the ripple to be due to
ESR, the output ripple will be less than 50mV at maximum
V
IN
and:
C
OUT
Required ESR < 2.2R
SENSE
C
OUT
>
1
8fR
SENSE
The first condition relates to the ripple current into the ESR
of the output capacitance while the second term guaran tees
that the output capacitance does not significantly discharge
during the operating frequency period due to ripple current.
The choice of using smaller output capaci tance increases
the ripple voltage due to the discharging term but can be
compensated for by using capacitors of very low ESR to
maintain the ripple voltage at or below 50mV. The I
TH
pin
OPTI-LOOP compensation compo nents can be optimized
to provide stable, high perfor mance transient response
regardless of the output capaci tors selected.
The selection of output capacitors for applications with
large load current transients is primarily determined by the
voltage tolerance specifications of the load. The resistive
component of the capacitor, ESR, multiplied by the load
current change, plus any output voltage ripple must be
within the voltage tolerance of the load.
