NFL18SP207X1A3D Datasheet NFL18SP207X1A3D, NFL18SP157X1A3D, NFL18SP507X1A3D | P1-P3

Spec. No. JENF243D-0003J-01 P1/ 8

MURATA MFG.CO., LTD.

Reference

Only

Chip EMIFIL® LC Combined Monolithic

NFL18SP□□□X1A3□ Reference Specification

1. Scope

This reference specification applies to Chip EMIFIL® LC Combined Monolithic Type NFL18SP Series.

2. Part Numbering

L 18 SP 157 X 1A 3 D

Product ID Structure Dimension Features Cut-off Frequency Characteristics Rated Voltage Electrode Packaging Code

(LW) (D : Taping / B : Bulk)

3. Rating

Customer

Part Number

MURATA

Part Number

Cut-off

Frequency

[MHz]

Capacitance

[pF]

Inductance

(L)

[nH]

Resistance

[ max.]

Insulation

Resistance

[M min.]

Rated

Voltage

[V(DC)]

Rated

Current

[mA(DC)]

Withstanding

Voltage

[V(DC)]

NFL18SP157X1A3D

150 34±20% 100±20%

3.0

1000 10 100 30

NFL18SP157X1A3B

NFL18SP207X1A3D

200 24±20% 80±20%

NFL18SP207X1A3B

NFL18SP307X1A3D

300 19±20% 60±20%

NFL18SP307X1A3B

NFL18SP507X1A3D

500 11±20% 38±20% 2.0

NFL18SP507X1A3B

 Operating Temperature : -55°C to +125°C (Includes self-heating.)

 Storage Temperature : -55°C to +125°C

4. Standard Testing Condition

< Unless otherwise specified > < In case of doubt >

Temperature : Ordinary Temp. / 15 °C to 35 °C Temperature : 20 °C ± 2 °C

Humidity : Ordinary Humidity / 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH)

Atmospheric pressure : 86 kPa to 106 kPa

5. Style and Dimensions

■ Equivalent Circuits

■ Unit Mass (Typical value)

0.004g

■ Insertion Loss Characteristics (I.L.) (Typ.)

(50Ωsystem)

Input

(1)

Out put

(2)

GND

(3)

※

No Polarity

0.2min.

(1)

(2)

(3)

:Electrode

(in mm)

0.6±0.1

1.6±0.1

0.4±0.1 0.3±0.1

0.8±0.1

0.3±0.1

0.15±0.1

(3)

(1)

Spec. No. JENF243D-0003J-01 P2/ 8

MURATA MFG.CO., LTD.

Reference

Only

6. Marking

No marking

7. Electrical Performance

No. Item Specification Test Method

7.1 Capacitance

(Cap.)

Meet item 3.

· Frequency : 1±0.1MHz

· Voltage : 1±0.2V(rms)

7.2 Inductance

(L)

· Frequency : 10±1MHz

· Voltage : 1±0.2V(rms)

7.3 DC Resistance

(Rdc)

Measured with 10mA max.

Measured between terminal (1)-(3). (ref. Item5)

7.4 Insulation

Resistance(I.R.)

· Voltage : Rated Voltage

· Time : 1 minutes max.

7.5 Withstanding

Voltage

Products shall not be damaged.

· Test Voltage : 30V(DC)

· Time : 1 to 5 s

· Charge Current : 50 mA max.

8. Mechanical Performance

No. Item Specification Test Method

8.1 Appearance and

Dimensions

Meet item 5. Visual Inspection and measured with Slide

Calipers.

8.2 Solderability Electrodes shall be at least 90%

covered with new solder coating.

· Flux : Ethanol solution of rosin, 25(wt)%

· Pre-heat : 150 ± 10°C, 60 to 90s

· Solder : Sn-3.0Ag-0.5Cu

· Solder Temperature : 240 ± 3°C

· Immersion Time : 3±1 s

· Immersion and emersion rates : 25mm / s

8.3 Resistance to

soldering heat

Meet Table 1.

Table 1

· Flux : Ethanol solution of rosin, 25(wt)%

· Pre-heat : 150 ± 10°C, 60 to 90s

· Solder : Sn-3.0Ag-0.5Cu

· Solder Temperature : 270 ± 5°C

· Immersion Time : 10 ± 1 s

· Immersion and emersion rates : 25mm / s

8.4 Bending

Strength

Meet Table 2.

Table 2

It shall be soldered on the glass-epoxy substrate

(t = 1.0mm).

· Deflection : 2.0 mm

· Keeping Time : 30 s

(in mm)

8.5 Drop Products shall be no failure after

tested.

It shall be dropped on concrete or steel board.

· Method : Free fall

· Height : 1m

· Attitude from which the product is dropped

: 3 directions

· The Number of Time : 3 times for each direction

(Total 9 times)

Appearance No damaged

Cap. Change within ± 5%

L Change within ± 5%

I.R. meet item 3

Appearance No damaged

Cap. Change within ± 5%

R230

Deflection

Product

Pressure jig

Spec. No. JENF243D-0003J-01 P3/ 8

MURATA MFG.CO., LTD.

Reference

Only

No. Item Specification Test Method

8.6 Bonding

Strength

The electrodes shall be no failure after

tested.

It shall be soldered on the glass-epoxy substrate.

· Applying Force (F) : 9.8 N

· Applying Time : 30 s

(in mm)

8.7 Vibration Meet Table 1. It shall be soldered on the glass-epoxy substrate.

· Oscillation Frequency : 10 to 2000 to 10Hz for

20 minutes.

· Total amplitude 1.5 mm or Acceleration amplitude

200m/s

whichever is smaller.

· Time : A period of 2 hours in each of 3 mutually

perpendicular directions. (Total 6 hours)

9. Environment Performance

It shall be soldered on the glass-epoxy substrate.

No. Item Specification Test Method

9.1 Temperature

Cycling

Meet Table 1.

· 1 Cycle

1 step: -55 ±

°C / 30 ±

minutes

2 step: Room Temperature / 3 minutes within.

3 step: +125 ±

°C / 30 ±

minutes

4 step: Room Temperature / 3 minutes within.

· Total of 10 cycles

· Then measured after exposure in the room

condition for 24±2 hours.

9.2 Humidity

· Temperature : 40 ± 2 °C

· Humidity : 90 to 95%(RH)

· Time : 500±

hours

· Then measured after exposure in the room

condition for 24±2 hours.

9.3 Heat Life

· Temperature : 125 ± 2 °C

· Test Voltage : Rated Voltage 200%

· Charge Current : 50 mA max.

· Time : 1000 ±

hours

· Then measured after exposure in the room

condition for 24±2 hours.

10. Specification of Packaging

10.1. Appearance and Dimensions (8mm-wide paper tape)



(in mm)

0.4

1.2

1.6

0.5



1.5±

4.0±0.1

1.85±0.1

2.0±0.1

3.5±0.1

1.75±0.1

8.0±0.3

0.1

1.05±0.1

4.0±0.1

0.9max.

Direction of feed

Sporocket Hole

2.0±0.05

3.5±0.05

P1-P3 P4-P6 P7-P8

NFL18SP207X1A3D

Mfr. #:

Buy NFL18SP207X1A3D

Manufacturer:

Murata Electronics

Description:

EMI Filter Circuits 0603 24pF +/-20% 80nH +/-20% 100mA

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

NFL18SP207X1A3D

NFL18SP207X1A3D

Products related to this Datasheet