NX3DV2567 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2011. All rights reserved.
Product data sheet Rev. 2 — 9 November 2011 5 of 20
NXP Semiconductors
NX3DV2567
Low-ohmic four-pole double-throw analog switch
[1] The minimum input voltage rating may be exceeded if the input current rating is observed.
[2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
[3] For HXQFN16U package: above 135 C the value of P
tot
derates linearly with 16.9 mW/K.
[4] For XQFN16 package: above 133 C the value of P
tot
derates linearly with 14.5 mW/K.
10. Recommended operating conditions
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nYn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current will flow from terminal nYn. In this case, there
is no limit for the voltage drop across the switch.
[2] Applies to control signal levels.
11. Static characteristics
P
tot
total power dissipation T
amb
= 40 Cto+125C
[3][4]
-250mW
Table 5. Limiting values …continued
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
Table 6. Recommended operating conditions
Symbol Parameter Conditions Min Max Unit
V
CC
supply voltage 1.4 4.3 V
V
I
input voltage select input S 0 4.3 V
V
SW
switch voltage
[1]
0V
CC
V
T
amb
ambient temperature 40 +125 C
t/V input transition rise and fall rate V
CC
= 1.4 V to 4.3 V
[2]
- 200 ns/V
Table 7. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions T
amb
= 25 C T
amb
= 40 C to +125 C Unit
Min Typ Max Min Max
(85 C)
Max
(125 C)
V
IH
HIGH-level
input voltage
V
CC
= 1.4 V to 1.6 V 0.9 - - 0.9 - - V
V
CC
= 1.65 V to 1.95 V 0.9 - - 0.9 - - V
V
CC
= 2.3 V to 2.7 V 1.1 - - 1.1 - - V
V
CC
= 2.7 V to 3.6 V 1.3 - - 1.3 - - V
V
CC
= 3.6 V to 4.3 V 1.4 - - 1.4 - - V
V
IL
LOW-level
input voltage
V
CC
= 1.4 V to 1.6 V - - 0.3 - 0.3 0.3 V
V
CC
= 1.65 V to 1.95 V - - 0.4 - 0.4 0.3 V
V
CC
= 2.3 V to 2.7 V - - 0.4 - 0.4 0.4 V
V
CC
= 2.7 V to 3.6 V - - 0.5 - 0.5 0.5 V
V
CC
= 3.6 V to 4.3 V - - 0.6 - 0.6 0.6 V
I
I
input leakage
current
select input S;
V
I
=GNDto4.3V;
V
CC
= 1.4 V to 4.3 V
--- -0.5 1 A
