ADV7533 Data Sheet
Rev. A | Page 6 of 12
The power supply noise sensitivity of the ADV7533 is frequency dependent. Therefore, the maximum noise limit for the PVDD is
specified in mV rms vs. frequency (see Figure 2).
70
60
50
40
30
20
10
0
1 10 100 1k 10k
09821-102
NOISE LIMIT (mV rms)
FREQUENCY (Hz)
Figure 2. PVDD Maximum Noise Limit
MIPI/DSI SPECIFICATIONS
Unless noted, timing and levels comply with MIPI DPHY standards.
Table 2. DSI High Speed (HS) Specifications
Parameters Symbol
ADV7533
Temp Test Level Min Typ Max Unit
DC SPECIFICATIONS
DSI Input Common Mode Voltage V
CMRX
25°C VII 70 330 mV
DSI Input High Threshold V
IDTH
25°C VII 70 mV
DSI Input Low Threshold V
IDTL
25°C VII −70 mV
DSI Single-Ended Input High Voltage V
IHHS
25°C VII 460 mV
DSI Single-Ended Input Low Voltage V
ILHS
25°C VII −40 mV
DSI Single-Ended Threshold for Termination Enable
V
TERM-EN
25°C
VII
450
mV
Differential Input Impedance Z
ID
25°C VII 80 100 125
AC SPECIFICATIONS
Single Channel Data Rate 25°C IV 200 800 Mbps
Data to Clock Setup Time t
SETUP
25°C VII 0.15 UI
INST
Data to Clock Hold Time t
HOLD
25°C VII 0.15 UI
INST
DSI Clock Duty Cycle 25°C VII 45 50 55 %
Common-Mode Interference Beyond 450 MHz ∆V
CMRX(HF)
25°C VII 100 mV
Common-Mode Interference 50 MHz to 450 MHz ∆V
CMRX(LF)
25°C VII −50 +50 mV
Common-Mode Termination C
CM
25°C VII 60 pF
Data Sheet ADV7533
Rev. A | Page 7 of 12
REFERENCE TIME
CLKp
CLKn
0.5UI
INST
+
1UI
INST
t
SETUP
t
SKEW
t
CLKp
t
HOLD
09821-002
Figure 3. DSI Data to Clock Timing Definitions
Table 3. DSI Low Power Specifications
Parameter Symbol Temp Test Level Min Typ Max Unit
DC SPECIFICATIONS
Logic 1 Input Voltage V
IH
25°C VII 880 mV
Logic 0 Input Voltage, Not in ULP State V
IL
25°C VII 550 mV
Input Hysteresis V
HYST
25°C VII 25 mV
AC SPECIFICATIONS
Input Pulse Rejection E
SPIKE
25°C VII 300 V × ps
Minimum Pulse Width Response T
MIN-RX
25°C VII 20 ns
Peak Interference Amplitude V
INT
25°C VII 200 mV
Interference Frequency f
INT
25°C VII 450 MHz
Table 4. DSI Pin Specifications
Parameter Conditions
ADV7533
Temp Test Level Min Typ Max Unit
DC SPECIFICATIONS
Pin Signal Voltage Range V
PIN
25°C VII −50 +1350 mV
Pin Leakage Current I
LEAK
25°C VII −10 +10 μA
Ground Shift V
GNDSH
25°C VII −50 +50 mV
Transient Pin Voltage Level V
PIN
(absmax) 25°C VII −0.15 +1.45 V
Maximum Transient Time Above V
PIN
(Max) or Below V
PIN
(Min)
T
VPIN
(absmax) 25°C VII 20 ns
ADV7533 Data Sheet
Rev. A | Page 8 of 12
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter Rating
Digital Inputs—I
2
C (DDCSDA, DDCSCL,
SDA, SCL) and HPD
5.5 V to −0.3 V
Digital Inputs—MIPI/DSI 1.8 V
Digital Inputs—Video/Audio Inputs,
CEC_IO, CEC_CLK
3.63 V to −0.3 V
Digital Output Current 20 mA
Operating Temperature Range −10°C to +85°C
Storage Temperature Range −40°C to +85°C
Maximum Junction Temperature 150°C
Maximum Case Temperature 150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
EXPLANATION OF TEST LEVELS
I 100% production tested.
II
100% production tested at 25°C and sample tested at specified temperatures.
III Sample tested only.
IV Parameter is guaranteed by design and characterization testing.
V Parameter is a typical value only.
VI 100% production tested at 25°C; guaranteed by design and characterization testing.
VII Limits defined by HDMI specification; guaranteed by design and characterization testing.
VIII Parameter is guaranteed by design.

ADV7533BCBZ-RL7

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Video ICs HDMI & NDA required see product comment
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet