OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

N57L5125TBD10TG

P1-P3P4-P6P7-P8
© Semiconductor Components Industries, LLC, 2016
August, 2016 − Rev. P0
1 Publication Order Number:
N57L5125/D
N57L5125
Product Preview
32‐tap Digital
Potentiometers (POTs)
with 2‐wire Interface
Description
N57L5125 linear-taper digital POTs perform the same function as a
mechanical potentiometer or a variable resistor. This device consists
of a fixed resistor and a wiper contact with 32-tap points that are
digitally controlled through a 2-wire up/down serial interface.
The N57L5125 is configured as a potentiometer. Three resistance
values are available: 10 kW, 50 kW and 100 kW. All devices are
available in a space-saving 6-pin SOT−23 package.
Features
• 0.3 mA Ultra-low Standby Current
• Single-supply Operation: 2.7 V to 5.5 V
• Glitchless Switching between Resistor Taps
• Power-on Reset to Midscale
• 2-wire Up/Down Serial Interface
• Resistance Values: 10 kW, 50 kW and 100 kW
• Low Wiper Resistance: 80 W
• These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
• LCD Screen Adjustment
• Volume Control
• Mechanical Potentiometer Replacement
• Gain Adjustment
• Line Impedance Matching
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
www.onsemi.com
PIN CONNECTIONS
(Top View)
SOT−23
TB SUFFIX
CASE 527AJ
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
ORDERING INFORMATION
GND
1
6H
2
3
4
W
5
N57L5125
SOT−23
U/D
V
DD
CS
MARKING
DIAGRAM
1
XXX MG
G
XXX = Specific Device Code
M = Date Code
G = Pb−Free Package
(Note: Microdot may be in either location)
N57L5125
www.onsemi.com
2
32−POSITION
DECODER
UP−DOWN
COUNTER
GND
H
GND
W
Figure 1. Functional Diagram
U/D
CS
V
DD
Table 1. PIN DESCRIPTIONS
Pin Num-
ber
Pin
Name
Description
1 V
DD
Power Supply
2 GND Ground
3 U/D Up/Down Control Input. With CS low, a low-to-high transition increments or decrements the wiper
position.
4 CS Chip Select Input. A high-to-low CS transition determines the mode: increment if U/D is high, or
decrement if U/D
is low.
5 W Wiper Terminal of Resistor
6 H High Terminal of Resistor
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameters Ratings Units
V
DD
to GND −0.3 to +6 V
All Other Pins to GND −0.3 to (V
DD
+ 0.3) V
Input and Output Latch−Up Immunity ±200 mA
Maximum Continuous Current into H, L and W
100 kW
50 kW
10 kW
±0.6
±1.3
±1.3
mA
Continuous Power Dissipation (T
A
= +70°C)
6-pin SC−70 (Note 1)
245
mW
Operating Temperature Range −40 to +85 °C
Junction Temperature +150 °C
Storage Temperature Range −65 to +150 °C
Soldering Temperature (soldering, 10 sec) +300 °C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Derate 3.1 mW/°C above T
A
= +70°C
N57L5125
www.onsemi.com
3
Table 3. ELECTRICAL CHARACTERISTICS
(V
DD
= 2.7 V to 5.5 V, V
H
= V
DD
, V
L
= 0, T
A
= −40°C to +85°C. Typical values are at V
DD
= 2.7 V, T
A
= 25°C, unless otherwise noted.)
Parameter
Symbol Conditions Min Typ Max Units
DC PERFORMANCE
Resolution 32 Taps
End-to-End Resistance (−00) 80 100 120 kW
End-to-End Resistance (−50) 40 50 60
End-to-End Resistance (−10) 8 10 12
End-to-End Resistance Tempco TC
R
30 300 ppm/°C
Ratiometric Resistance Tempco 5 ppm/°C
Integral Nonlinearity INL ±0.5 LSB
Differential Nonlinearity DNL ±0.5 LSB
Full-Scale Error ±0.1 LSB
Zero-Scale Error 1 LSB
Wiper Resistance R
W
80 200
W
DIGITAL INPUTS
Input High Voltage
V
IH
0.7 x V
DD
V
Input Low Voltage V
IL
0.3 x V
DD
V
TIMING CHARACTERISTICS (Figures 5, 6)
U/D
Mode to CS Setup t
CU
25 ns
CS to U/D Step Setup t
CI
50 ns
CS to U/D Step Hold t
IC
25 ns
U/D Step Low Period t
IL
25 ns
U/D Step High Period t
IH
25 ns
Up/Down Toggle Rate (Note 2) f
TOGGLE
1 MHz
Output Settling Time (Note 3) t
SETTLE
100 kW variable resistor
configuration, C
L
= 10 pF
1 ms
100 kW potentiometer
configuration, C
L
= 10 pF
0.25
POWER SUPPLY
Supply Voltage
V
DD
2.7 5.5 V
Active Supply Current (Note 4) I
DD
35
mA
Standby Supply Current (Note 5) I
SB
V
DD
= +5 V 0.3 1
mA
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Up/Down Toggle Rate: f
TOGGLE
= 1 / t
SETTLE
3. Typical settling times are dependent on end-to-end resistance.
4. Supply current measureed while changing wiper tap, f
TOGGLE
= 500 kHz.
5. Supply current measureed while wiper position is fixed.
P1-P3P4-P6P7-P8

N57L5125TBD10TG

Mfr. #:
Buy N57L5125TBD10TG
Manufacturer:
ON Semiconductor
Description:
Digital Potentiometer ICs 32-TAP DGTL W/2-WIRE POTENTIOMETER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet