LT6402-20
4
640220fa
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Input/Output Characteristics
–3dBBW –3dB Bandwidth 20mV
P-P
Differential (+OUT, –OUT) 200 300 MHz
0.1dBBW Bandwidth for 0.1dB Flatness 20mV
P-P
Differential (+OUT, –OUT) 30 MHz
0.5dBBW Bandwidth for 0.5dB Flatness 20mV
P-P
Differential (+OUT, –OUT) 80 MHz
SR Slew Rate 3.2V
P-P
Differential (+OUT, –OUT) 400 V/µs
t
s1%
1% Settling 1% Settling for a 1V
P-P
Differential Step
(+OUT, –OUT)
8ns
t
ON
Turn-On Time 100 ns
t
OFF
Turn-Off Time 1µs
Common Mode Voltage Control (V
OCM
Pin)
–3dBBW
CM
Common Mode Small-Signal –3dB
Bandwidth
0.1V
P-P
at V
OCM
, Measured Single-Ended at +OUT
and –OUT
200 MHz
SR
CM
Common Mode Slew Rate 1.3V to 3.4V Step at V
OCM
250 V/µs
Noise/Harmonic Performance Input/Output Characteristics
10MHz Signal
Second/Third Harmonic Distortion 2V
P-P
Differential (+OUTFILTERED, –OUTFILTERED) –85 dBc
2V
P-P
Differential (+OUT, –OUT) –85 dBc
Third-Order IMD 2V
P-P
Differential Composite (+OUTFILTERED,
–OUTFILTERED), f1 = 9.5MHz, f2 = 10.5MHz
–93 dBc
OIP3
10M
Output Third-Order Intercept Differential (+OUTFILTERED, –OUTFILTERED),
f1 = 9.5MHz, f2 = 10.5MHz (Note 5)
49.5 dBm
NF Noise Figure Measured Using DC954A Demo Board 12.3 dB
e
n10M
Input Referred Noise Voltage Density 1.85 nV/√Hz
1dB Compression Point R
L
= 100Ω (Note 5) 19.5 dBm
20MHz Signal
Second/Third Harmonic Distortion 2V
P-P
Differential (+OUTFILTERED, –OUTFILTERED) –81 dBc
2V
P-P
Differential (+OUT, –OUT) –81 dBc
Third-Order IMD 2V
P-P
Differential Composite (+OUTFILTERED,
–OUTFILTERED), f1 = 19.5MHz, f2 = 20.5MHz
–96 dBc
2V
P-P
Differential Composite (+OUT, –OUT),
R
L
= 400Ω, f1 = 19.5MHz, f2 = 20.5MHz
–91 dBc
OIP3
20M
Output Third-Order Intercept Differential (+OUTFILTERED, –OUTFILTERED),
f1 = 19.5MHz, f2 = 20.5MHz (Note 5)
51 dBm
NF Noise Figure Measured Using DC954A Demo Board 12.4 dB
e
n20M
Input Referred Noise Voltage Density 1.9 nV/√Hz
1dB Compression Point R
L
= 100Ω (Note 5) 18 dBm
T
A
= 25°C, V
CCA
= V
CCB
= V
CCC
= 5V, V
EEA
= V
EEB
= V
EEC
= 0V,
⎯
E
⎯
N
⎯
A
⎯
B
⎯
L
⎯
E = 0.8V, +INA shorted to +INB (+IN), –INA shorted to –INB (–IN), V
OCM
= 2.2V, Input common mode voltage = 2.2V, no R
LOAD
unless otherwise noted.
AC ELECTRICAL CHARACTERISTICS