Datasheet
4/13
BD52xx series BD53xx series
TSZ02201-0R7R0G300040-1-2
© 2012 ROHM Co., Ltd. All rights reserved.
18.Dec.2012 Rev.005
www.rohm.com
TSZ22111・15・001
●Absolute maximum ratings
Parameter Symbol Limits Unit
Power Supply Voltage V
DD
-GND -0.3 to +10 V
Output Voltage
Nch Open Drain Output
V
OUT
GND-0.3 to +10
V
CMOS Output GND-0.3 to V
DD
+0.3
Output Current Io 80 mA
Power
Dissipation
SSOP5
*1*3
Pd
540
mW
VSOF5
*2*3
210
Operating Temperature Topr -40 to +105 °C
Ambient Storage Temperature Tstg -55 to +125 °C
*1 Reduced by 5.4mW/°C when used over 25°C.
*2 Reduced by 2.1mW/°C when used over 25°C.
*3 When mounted on ROHM standard circuit board (70mm×70mm×1.6mm, glass epoxy board).
●Electrical characteristics (Unless Otherwise Specified Ta=-40 to 105°C)
Parameter Symbol Condition
Limit
Unit
Min. Typ. Max.
Detection Voltage V
DET
V
DD=HÆL, RL=470k
*1
V
DET(T)
×0.99
VDET(T)
VDET(T)
×1.01
V
VDET=2.5V
Ta=+25°C 2.475 2.5 2.525
Ta=-40°C to 85°C
2.417 - 2.580
Ta=85°C to 105°C
2.422 - 2.598
VDET=3.0V
Ta=+25°C 2.970 3.0 3.030
Ta=-40°C to 85°C
2.901 - 3.095
Ta=85°C to 105°C
2.906 - 3.117
VDET=3.3V
Ta=+25°C 3.267 3.3 3.333
Ta=-40°C to 85°C
3.191 - 3.405
Ta=85°C to 105°C
3.196 - 3.429
VDET=4.2V
Ta=+25°C 4.158 4.2 4.242
Ta=-40°C to 85°C
4.061 - 4.334
Ta=85°C to 105°C
4.068 - 4.364
VDET=4.8V
Ta=+25°C 4.752 4.8 4.848
Ta=-40°C to 85°C
4.641 - 4.953
Ta=85°C to 105°C
4.649 - 4.988
Circuit Current when ON IDD1 VDD=VDET-0.2V
V
DET
=2.3-3.1V - 0.80 2.40
µA
V
DET
=3.2-4.2V - 0.85 2.55
V
DET
=4.3-5.2V - 0.90 2.70
V
DET
=5.3-6.0V - 0.95 2.85
Circuit Current when OFF IDD2 VDD=VDET+2.0V
V
DET
=2.3-3.1V - 0.75 2.25
µA
V
DET
=3.2-4.2V - 0.80 2.40
V
DET
=4.3-5.2V - 0.85 2.55
V
DET
=5.3-6.0V - 0.90 2.70
Operating Voltage Range VOPL
VOL0.4V, Ta=25 to 105°C, RL=470k 0.95 - -
V
VOL0.4V, Ta=-40 to 25°C, RL=470k 1.20 - -
‘Low’ Output Voltage (Nch) VOL
V
DD=1.5V, ISINK = 0.4 mA, VDET=2.3-6.0V - - 0.5
V
VDD=2.4V, ISINK = 2.0 mA, VDET=2.7-6.0V - - 0.5
‘High’ Output Voltage (Pch) VOH
V
DD=4.8V, ISOURCE=0.7 mA, VDET(2.3V to 4.2V) VDD-0.5 - -
V
VDD=6.0V, ISOURCE=0.9 mA, VDET(4.3V to 5.2V) VDD-0.5 - -
VDD=8.0V, ISOURCE=1.1 mA, VDET(5.3V to 6.0V) VDD-0.5 - -
VDET (T) : Standard Detection Voltage (2.3V to 6.0V, 0.1V step)
R
L
: Pull-up resistor to be connected between VOUT and power supply.
Design Guarantee. (Outgoing inspection is not done on all products.)
*1 Guaranteed at Ta=25°C.
