LTM2882
4
2882fd
swiTching characTerisTics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. LTM2882-3 V
CC
= 3.3V, LTM2882-5 V
CC
= 5.0V, V
L
= V
CC
, and GND =
GND2 = 0V, ON = V
L
unless otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
Maximum Data Rate
(T1IN to T1OUT, T2IN to T2OUT)
R
L
= 3kΩ, C
L
= 2.5nF (Note 3)
l
100 kbps
R
L
= 3kΩ, C
L
= 1nF (Note 3)
l
250 kbps
R
L
= 3kΩ, C
L
= 250pF (Note 3)
l
1000 kbps
Maximum Data Rate (DIN to DOUT) C
L
= 15pF (Note 3)
l
10 Mbps
Driver
Driver Slew Rate (6V/t
THL
or t
TLH
) R
L
= 3kΩ, C
L
= 50pF (Figure 1)
l
150 V/µs
t
PHLD
, t
PLHD
Driver Propagation Delay R
L
= 3kΩ, C
L
= 50pF (Figure 1)
l
0.2 0.5 µs
t
SKEWD
Driver Skew |t
PHLD
– t
PLHD
| R
L
= 3kΩ, C
L
= 50pF (Figure 1) 40 ns
t
PZHD
, t
PZLD
Driver Output Enable Time DE = ↑ , R
L
= 3kΩ, C
L
= 50pF (Figure 2)
l
0.6 2 µs
t
PHZD
, t
PLZD
Driver Output Disable Time DE = ↓ , R
L
= 3kΩ, C
L
= 50pF (Figure 2)
l
0.3 2 µs
Receiver
t
PHLR
, t
PLHR
Receiver Propagation Delay C
L
= 150pF (Figure 3)
l
0.2 0.4 µs
t
SKEWR
Receiver Skew |t
PHLR
– t
PLHR
| C
L
= 150pF (Figure 3) 40 ns
t
RR
, t
FR
Receiver Rise or Fall Time C
L
= 150pF (Figure 3)
l
60 200 ns
Auxiliary Channel
t
PHLL
, t
PLHL
Propagation Delay C
L
= 15pF, t
R
and t
F
< 4ns (Figure 4)
l
60 100 ns
t
RL
, t
FL
Rise or Fall Time C
L
= 150pF (Figure 4)
l
60 200 ns
Power Supply
Power-Up Time ON = ↑ to V
CC2(MIN)
l
0.2 2 ms
isolaTion characTerisTics
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. LTM2882-3 V
CC
= 3.3V, LTM2882-5 V
CC
= 5.0V, V
L
= V
CC
, and GND =
GND2 = 0V, ON = V
L
unless otherwise noted.
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
ISO
Rated Dielectric Insulation Voltage 1 Minute, Derived from 1 Second Test 2500 V
RMS
1 Second (Note 5) ±4400 V
Common Mode Transient Immunity V
L
= ON = 3.3V, V
CM
= 1kV, ∆t = 33ns (Note 2) 30 kV/µs
V
IORM
Maximum Working Insulation Voltage (Notes 2, 5) 560
400
V
PEAK
V
RMS
Partial Discharge V
PR
= 1050 V
PEAK
(Notes 2, 5) 5 pC
Input to Output Resistance (Notes 2, 5) 10
9
Ω
Input to Output Capacitance (Notes 2, 5) 6 pF
Creepage Distance (Notes 2, 5) 9.48 mm
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Guaranteed by design and not subject to production test.
Note 3: Maximum Data Rate is guaranteed by other measured parameters
and is not tested directly.
Note 4: This device includes over-temperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C when overtemperature protection is active.
Continuous operation above specified maximum operating junction
temperature may result in device degradation or failure.
Note 5: Tests performed from GND to GND2, all pins shorted each side of
isolation barrier.