OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HTMS-3/4-9

P1-P3P4-P6
RW-2500/1 Revision 4
Page 4 of 6
September 2014
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is
error-free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity
reserves the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties
regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in
this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for
the latest dimensions and design specifications.
If this document is printed it becomes uncontrolled.
TABLE 1
Dimensions
USA DESCRIPTIONS
As Supplied
Recovered
Inside Diameter
Marking Length
Inside Diameter
Product Description
Minimum
Minimum
Maximum
Wall Thickness
in.
mm.
in.
mm.
in.
mm.
in.
mm.
HTTMS-3/32-1.50
0.093
2.36
1.50
39.41
0.031
0.79
0.016 + 0.003
0.41+0.08
HTTMS-1/8-1.50
0.125
3.17
1.50
39.41
0.062
1.57
0.013 + 0.003
0.33+0.08
HTTMS-3/16-1.50
0.187
4.74
1.50
39.41
0.093
2.36
0.015 + 0.003
0.38+0.08
HTTMS-1/4-1.50
0.250
6.35
1.50
39.41
0.125
3.17
0.015 + 0.003
0.38+0.08
HTTMS-3/8-1.50
0.375
9.50
1.50
39.41
0.187
4.74
0.015 + 0.003
0.38+0.08
HTTMS-1/2-1.50
0.475
12.07
1.50
39.41
0.250
6.35
0.015 + 0.003
0.38+0.08
HTTMS-3/4-1.50
N/A
N/A
1.50
39.41
0.375
9.53
0.017 + 0.003
0.43+0.08
HTTMS-3/32-1.75
0.093
2.36
1.75
44.45
0.031
0.79
0.016 + 0.003
0.41+0.08
HTTMS-1/8-1.75
0.125
3.17
1.75
44.45
0.062
1.57
0.013 + 0.003
0.33+0.08
HTTMS-3/16-1.75
0.187
4.74
1.75
44.45
0.093
2.36
0.015 + 0.003
0.38+0.08
HTTMS-1/4-1.75
0.250
6.35
1.75
44.45
0.125
3.17
0.015 + 0.003
0.38+0.08
HTTMS-3/8-1.75
0.375
9.50
1.75
44.45
0.187
4.74
0.015 + 0.003
0.38+0.08
HTTMS-3/4-1.75
N/A
N/A
1.75
44.45
0.375
9.53
0.017 + 0.003
0.43+0.08
EUROPEAN DESCRIPTIONS
As Supplied
Recovered
Inside Diameter
Marking Length
Inside Diameter
Product Description
Minimum
Minimum
Maximum
Wall Thickness
in.
mm.
in.
mm.
in.
mm.
in.
mm.
HTMS-3/32
0.093
2.36
1.89
48
0.031
0.79
0.016 + 0.003
0.41+0.08
HTMS-1/8
0.125
3.17
1.89
48
0.062
1.57
0.013 + 0.003
0.33+0.08
HTMS-3/16
0.187
4.74
1.89
48
0.093
2.36
0.015 + 0.003
0.38+0.08
HTMS-1/4
0.250
6.35
1.89
48
0.125
3.17
0.015 + 0.003
0.38+0.08
HTMS (HTTMS)-3/8
0.375
9.50
1.85
47
0.187
4.74
0.015 + 0.003
0.38+0.08
HTMS (HTTMS)-1/2
0.475
12.07
1.81
46
0.250
6.35
0.015 + 0.003
0.38+0.08
HTMS (HTTMS)-3/4
N/A
N/A
1.65
42
0.375
9.53
0.017 + 0.003
0.43+0.08
TABLE 2
Mandrel Dimensions for Heat Shock, Heat Aging and Low Temperature Flexibility
Tubing Size
Mandrel Diameter
in
mm
3/32 through 3/16
5/16
7.9
1/4 through 3/4
3/4
19.0
RW-2500/1 Revision 4
Page 5 of 6
September 2014
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is
error-free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity
reserves the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties
regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in
this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for
the latest dimensions and design specifications.
If this document is printed it becomes uncontrolled.
TABLE 3 Requirements
PROPERTY
UNIT
REQUIREMENT
RW-2500
TEST METHOD
PHYSICAL
Dimensions
mm (inches)
In accordance with Table 1
RW-2500 Section
4.3.1.1
ASTM D 2671
Dimensional Recovery
3 minutes at 200°C (392°F)
mm (inches)
In accordance with Table 1
Longitudinal Change
3 minutes at 200°C (392°F)
Percent
10 maximum
Tensile Strength
MPa (psi)
34.5 (5000) minimum
RW-2500 Section
4.3.2.1
ASTM D 2671
Ultimate Elongation
Percent
200 minimum
2 inches/minute
Specific Gravity
---
1.8 maximum
RW-2500 Section
4.3.3 ASTM D 2671
Low Temperature Flexibility
4 hours at -55°C (-67°F)
---
No cracking
RW-2500 Section
4.3.5.1
Heat Shock
4 hours at 275°C (527°F)
---
No dripping, flowing, or cracking
RW-2500 Section
4.3.6.1
Heat Aging
168 hours at 225°C (437°F)
---
No cracking
RW-2500 Section
4.3.7.1
Copper Contact Corrosion
16 hours at 150° C (302°F)
---
No pitting or blackening of core
RW-2500 Section
4.3.14.1
Pull-Off Force
Size: 3/32 through 1/8
N (Pounds)
22 (5.0) maximum
RW-2500 Section
4.3.8
Size: 3/16 through 1/4
N (Pounds)
31 (7.0) maximum
Size: 3/8 through 3/4
N (Pounds)
44 (10.0) maximum
Vacuum Outgassing
TML (Total Mass Loss)
VCM (Volatile Condensable
Material)
Percent
Percent
1.0 maximum
0.1 maximum
RW-2500 Section
4.3.18
ASTM E 595
Temperature Cycling
6 cycles of:
0.5 hr/-196°C (-321° F)
0.5 hr/200°C (392° F)
No cracking
RW-2500 Section
4.3.23
ELECTRICAL
Dielectric Strength
Size: 3/32 through 3/16
1/4 through 1/2
kV/mm (V/mil)
31.5 (800) minimum
23.6 (600) minimum
RW-2500 Section
4.3.11.1
ASTM D 2671
Volume Resistivity
ohm-cm
10
12
minimum
RW-2500 Section
4.3.12.1 ASTM D
2671
CHEMICAL
Corrosive Effect
16 hours at 150°C (302°F)
---
Non Corrosive
RW-2500 Section
4.3.13.1
ASTM D 2671
Flammability
UL 224
ASTM D 876 Average time of burning
Seconds
Pass VW-1
15 maximum
RW-2500 Section
4.3.15.1 and
Section 4.3.15.2
Fungus Resistance
---
Rating of 1 or less
ASTM G 21
RW-2500/1 Revision 4
Page 6 of 6
September 2014
TE CONNECTIVITY, SWINDON, UK
While TE Connectivity has made every reasonable effort to ensure the accuracy of the information in this specification, TE Connectivity does not guarantee that it is
error-free, nor does TE Connectivity make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. TE Connectivity
reserves the right to make any adjustments to the information contained herein at any time without notice. TE Connectivity expressly disclaims all implied warranties
regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in
this document are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult TE Connectivity for
the latest dimensions and design specifications.
If this document is printed it becomes uncontrolled.
Additional notes for Low Temperature Flexibility
For sizes smaller than 1/4 inch, recover three 6-inch long specimens and cool to room temperature.
For sizes 1/4 inch and larger, prepare test strips as follows: Recover three 6-inch long sections of tubing, and while they are still
hot, slit longitudinally, and flatten between metal plates. Cool to room temperature, remove metal plates, and cut into 1/4-inch wide
strips.
Place the specimens in a cold chamber with the mandrel specified in Table 2 at -55°C (-67°F) for 4 hours. While still in the cold
chamber, and at this same temperature, wrap the specimens around the mandrel not less than 360° in approximately 2 seconds.
P1-P3P4-P6

HTMS-3/4-9

Mfr. #:
Buy HTMS-3/4-9
Manufacturer:
Raychem / TE Connectivity
Description:
Wire Labels & Markers HTMS-3/4-9
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet