AOT480L/AOB480L
Symbol Min Typ Max Units
BV
DSS
80 V
V
DS
=80V, V
GS
=0V 10
T
J
=55°C 50
I
GSS
100 nA
V
GS(th)
Gate Threshold Voltage
2 2.8 4 V
I
D(ON)
500 A
3.7 4.5
T
J
=125°C 6.1 7.3
4.2 5.5 mΩ
3.4 4.2
mΩ
3.9 5.2 mΩ
g
FS
60 S
V
SD
0.6 1 V
I
S
180 A
C
iss
5200 6520 7820 pF
C
oss
570 810 1060 pF
C
rss
185 310 430 pF
R
g
0.3 0.64 1 Ω
Q
g
(10V) 92 116 140 nC
Q
gs
24 30 36 nC
Q
gd
23 38 53 nC
t
D(on)
31.5 ns
t
r
33 ns
t
D(off)
46 ns
t
f
17.5 ns
t
rr
20 28 36 ns
Q
rr
90 132 170
nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Body Diode Reverse Recovery Time
Drain-Source Breakdown Voltage
On state drain current
I
D
=250µA, V
GS
=0V
V
GS
=10V, V
DS
=5V
V
GS
=10V, I
D
=20A
Reverse Transfer Capacitance
I
F
=20A, dI/dt=500A/µs
V
GS
=0V, V
DS
=40V, f=1MHz
SWITCHING PARAMETERS
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
I
DSS
µA
V
DS
=5V
,
I
D
=250µA
V
DS
=0V, V
GS
= ±25V
Zero Gate Voltage Drain Current
Gate-Body leakage current
Forward Transconductance
Diode Forward Voltage
Static Drain-Source On-Resistance
R
DS(ON)
mΩ
TO220
I
S
=1A,V
GS
=0V
V
DS
=5V, I
D
=20A
V
GS
=7V, I
D
=20A
TO220
V
GS
=10V, I
D
=20A
TO263
V
GS
=7V, I
D
=20A
TO263
Gate resistance
V
GS
=0V, V
DS
=0V, f=1MHz
Turn-Off Fall Time
Total Gate Charge
V
GS
=10V, V
DS
=40V, I
D
=20A
Gate Source Charge
Gate Drain Charge
Body Diode Reverse Recovery Charge
I
F
=20A, dI/dt=500A/µs
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
DYNAMIC PARAMETERS
Turn-On Rise Time
Turn-Off DelayTime
V
GS
=10V, V
DS
=40V, R
L
=2Ω,
R
GEN
=3Ω
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
Power dissipation P
DSM
is based on R
θJA
and the maximum allowed junction temperature of 150°C. The value in any given application depends
on the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allow s it.
B. The power dissipation P
D
is based on T
J(MAX)
=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=175°C. Ratings are based on low frequency and duty cycles to keep
initial T
J
=25°C.
D. The R
θJA
is the sum of the thermal impedence from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink,
assuming a maximum junction temperature of T
J(MAX)
=175°C. The SOA curve provides a single pulse ratin g.
G. The maximum current limited by package is 120A.
H. These tests are performed with the device mounted on 1 in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C.
Rev1: April 2010 www.aosmd.com Page 2 of 7
