OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HA3-5033-5

P1-P3P4-P6P7-P9P10-P12
1
HA-5033
250MHz Video Buffer
The HA-5033 is a unity gain monolithic IC designed for any
application requiring a fast, wideband buffer. Featuring a
bandwidth of 250MHz and outstanding differential phase/
gain characteristics, this high performance voltage follower
is an excellent choice for video circuit design. Other
features, which include a minimum slew rate of 1000V/s
and high output drive capability, make the HA-5033
applicable for line driver and high speed data conversion
circuits.
The high performance of this product is a result of the Intersil
Dielectric Isolation process. A major feature of this process
is that it produces both PNP and NPN high frequency
transistors which makes wide bandwidth designs, such as
the HA-5033, practical. Alternative process methods
typically produce a lower AC performance.
Ordering Information
Pinouts
HA-5033 (PDIP)
TOP VIEW
HA-5033 (METAL CAN)
TOP VIEW
Features
• Differential Phase Error . . . . . . . . . . . . . . . . 0.02 Degrees
• Differential Gain Error. . . . . . . . . . . . . . . . . . . . . . . 0.03%
• High Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . 1100V/s
• Wide Bandwidth (Small Signal) . . . . . . . . . . . . . . 250MHz
• Wide Power Bandwidth . . . . . . . . . . . . . . DC to 17.5MHz
• Fast Rise Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3ns
• High Output Drive. . . . . . . . . . . . . . 10V With 100 Load
• Wide Power Supply Range . . . . . . . . . . . . . 5V to 16V
• Replace Costly Hybrids
Applications
• Video Buffer
• High Frequency Buffer
• Isolation Buffer
• High Speed Line Driver
• Impedance Matching
• Current Boosters
• High Speed A/D Input Buffers
• Related Literature
- AN548, Designer’s Guide for HA-5033
PART
NUMBER
PART
MARKING
TEMP.
RANGE (°C) PACKAGE
PKG.
DWG. #
HA2-5033-2 HA2-5033-2 -55 to 125 12 Pin Metal Can T12.C
HA3-5033-5 HA3-5033-5 0 to 75 8 Ld PDIP E8.3
1
2
3
4
8
7
6
5
OUT
NC
SUB-
V-
V+
NC
NC
IN
STRATE
CASE
NC
12
1
2
3
4
11
10
9
8
7
6
5
V+
OUT
V-
NC
NC
NC
+IN
NC
NC
NC
Data Sheet February 6, 2006 FN2924.8
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2005, 2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
NO
T
R
E
C
O
M
M
E
N
D
E
D
F
O
R
N
E
W
D
E
S
I
G
N
S
N
O
R
E
CO
M
M
E
N
DE
D
R
E
P
L
A
CE
M
E
NT
c
o
n
t
a
c
t
o
u
r
T
e
c
h
n
ic
a
l
S
u
p
p
o
r
t
C
e
n
t
e
r
a
t
1
-
8
8
8
-
I
N
T
E
R
S
I
L
o
r
w
w
w
.
i
n
t
e
r
s
i
l
.
c
o
m
/
t
s
c
2
FN2924.8
Absolute Maximum Ratings Thermal Information
Voltage Between V+ and V- Pins . . . . . . . . . . . . . . . . . . . . . . . . 40V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V+ to V-
Output Current (Peak) (50ms On/1 Second Off) . . . . . . . . . 200mA
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 2000V
Operating Conditions
Temperature Ranges (Note 3)
HA-5033-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to 125°C
HA-5033-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 75°C
Thermal Resistance (Typical, Note 2)
JA
(°C/W)
JC
(°C/W)
Metal Can Package . . . . . . . . . . . . . . . 65 34
PDIP Package . . . . . . . . . . . . . . . . . . . 120 N/A
Maximum Junction Temperature (Note 1) . . . . . . . . . . . . . . . . . 175°C
Maximum Junction Temperature (Plastic Packages) . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including load conditions, must be designed to maintain the maximum junction temperature below 175°C for the metal can
package, and below 150°C for the plastic packages (See Figure 5.).
2.
JA
is measured with the component mounted on an evaluation PC board in free air.
3. The maximum operating temperature may have to be derated depending on the output load condition. See Figure 5 for more information.
Electrical Specifications V
SUPPLY
= 12V, R
S
= 50, R
L
= 100 C
L
= 10pF, Unless Otherwise Specified
PARAMETER
TEST
CONDITIONS
TEMP.
(°C)
HA-5033-2 HA-5033-5
UNITSMIN TYP MAX MIN TYP MAX
INPUT CHARACTERISTICS
Offset Voltage 25 - 5 15 - 5 15 mV
Full-625-625mV
Average Offset Voltage Drift Full - 33 - - 33 - V/°C
Bias Current 25 - 20 35 - 20 35 A
Full - 30 50 - 30 50 A
Input Resistance 25 - 3 - - 3 - M
Input Capacitance 25 - 1.6 - - 1.6 - pF
Input Noise Voltage 10Hz to 100MHz 25 - 20 - - 20 - V
P-P
TRANSFER CHARACTERISTICS
Voltage Gain R
L
= 100 25 0.93 - - 0.93 - - V/V
R
L
= 1k 25 0.93 0.99 - 0.93 0.99 - V/V
R
L
= 100 Full 0.92 - - 0.92 - - V/V
-3dB Bandwidth 25 - 250 - - 250 - MHz
OUTPUT CHARACTERISTICS
Output Voltage Swing R
L
= 100 Full 8 10 - 8 10 - V
R
L
= 1k, V
S
= 15V Full 11 12 - 11 12 - V
Output Current 25 80 100 - 80 100 - mA
Output Resistance 25 - 8 - - 8 -
Full Power Bandwidth V
OUT
= 1V
RMS
, R
L
= 1k 25 - 146 - - 146 - MHz
Full Power Bandwidth (Note 4) 25 15.9 17.5 - 15.9 17.5 - MHz
TRANSIENT RESPONSE
Rise Time V
OUT
= 500mV 25 - 4.6 - - 4.6 - ns
Propagation Delay 25 - 1 - - 1 - ns
HA-5033
3
FN2924.8
Overshoot 25 - 3 - - 3 - %
Slew Rate (Note 4) 25 1 1.1 - 1 1.1 - V/ns
Settling Time to 0.1% 25 - 50 - - 50 - ns
Differential Phase Error (Note 5) 25 - 0.02 - - 0.02 - Degree
Differential Gain Error (Note 5) 25 - 0.03 - - 0.03 - %
POWER SUPPLY CHARACTERISTICS
Supply Current 25 - 21 25 - 21 25 mA
Full - 21 30 - 21 30 mA
Power Supply Rejection Ratio Full 54 - - 54 - - dB
Harmonic Distortion V
IN
= 1V
RMS
at 100kHz 25 - <0.1 - - <0.1 - %
NOTES:
4. V
SUPPLY
= 15V, V
OUT
= 10V, R
L
= 1k.
5. Differential gain and phase error are nonlinear signal distortions found in video systems and are defined as follows: Differential gain error is
defined as the change in amplitude at the color subcarrier frequency as the picture signal is varied from blanking to white level. Differential phase
error is defined as the change in the phase of the color subcarrier as the picture signal is varied from blanking to white level. R
L
= 300.
Electrical Specifications V
SUPPLY
= 12V, R
S
= 50, R
L
= 100 C
L
= 10pF, Unless Otherwise Specified (Continued)
PARAMETER
TEST
CONDITIONS
TEMP.
(°C)
HA-5033-2 HA-5033-5
UNITSMIN TYP MAX MIN TYP MAX
Test Circuits and Waveforms
FIGURE 1. SLEW RATE AND SETTLING TIME
FIGURE 2. TRANSIENT RESPONSE
FIGURE 3. SETTLING TIME AND SLEW RATE
FIGURE 4. RISE TIME AND OVERSHOOT
+15V
R
L
OUTIN
0.1F
0.1F
-15V
+12V
100
OUTIN
0.1F
0.1F
-12V
10V
INPUT
90%
OUTPUT
10%
ERROR BAND
10mV FROM
FINAL VALUE
SLEW
V/t
0V
V
RATE =
t
SETTLING TIME
INPUT
90%
OUTPUT
10%
0V
500mV
OVERSHOOT
NOTE: Measured on both
positive and negative transitions.
HA-5033
P1-P3P4-P6P7-P9P10-P12

HA3-5033-5

Mfr. #:
Buy HA3-5033-5
Manufacturer:
Renesas / Intersil
Description:
IC VIDEO BUFFER 250MHZ 8DIP
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet