Data Sheet ADP3605
Rev. B | Page 3 of 12
SPECIFICATIONS
V
IN
= 5.0 V at T
A
= 25°C, C
P
= C
O
= 4.7 µF, unless otherwise noted. The C
IN
, C
O
, and C
P
capacitors in the typical application circuit (see Figure 2)
are 4.7 µF. See Figure 2 conditions. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality
Control (SQC) methods.
Table 1.
Parameter Symbol Test Conditions/Comments Min Typ Max Unit
OPERATING SUPPLY RANGE V
S
3 6 V
I
S
40°C < T
A
< +85°C
3
6
mA
V
SD
= V
IN
, 40°C < T
A
< +85°C
2
15
µA
OUTPUT RESISTANCE
Open Loop R
O
9 Ω
OUTPUT RIPPLE VOLTAGE V
RIPPLE
C
IN
= C
O
= 4.7 µF, I
LOAD
= 60 mA 38 mV
I
LOAD
= 120 mA 75 mV
SWITCHING FREQUENCY f
S
V
IN
= 5 V, −40°C < T
A
< +85°C 212 250 288 kHz
SHUTDOWN
Logic Input High V
IH
2.4 V
Input Current I
IH
1 µA
Logic Input Low V
IL
0.4 V
Input Current I
IL
1 µA
ADP3605 Data Sheet
Rev. B | Page 4 of 12
ABSOLUTE MAXIMUM RATINGS
T
A
= 25°C, unless otherwise noted.
Table 2.
Parameter Rating
Input Voltage (V
IN
to GND, GND to V
OUT
) 7.5 V
Input Voltage (V
IN
to V
OUT
) 11 V
Output Short-Circuit Protection 1 sec
Power Dissipation, 8-Lead SOIC 660 mW
θ
JA
1
150°C/W
Operating Temperature Range 40°C to +85°C
Storage Temperature Range
65°C to +150°C
Lead Temperature (Soldering, 10 sec) 300°C
Vapor Phase (60 sec) 215°C
Infrared (15 sec) 220°C
1
θ
JA
is specified for the worst-case conditions with the device soldered on a
circuit board.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
Table 3. Alternative Capacitor Technologies
Type Life High Frequency Temperature Size Cost
Aluminum Electrolytic Capacitor Fair Fair Fair Small Low
Multilayer Ceramic Capacitor Long Good Poor Fair
1
High
Solid Tantalum Capacitor Above average Average Average Average Average
OS-CON Capacitor Above average Good Good Good Average
1
Refer to capacitor manufacturer's data sheet for operation below 0°C.
Table 4. Recommended Capacitor Manufacturers
Manufacturer Capacitor Capacitor Type
Sprague 672D, 673D, 674D, 678D Aluminum electrolytic
Sprague 675D, 173D, 199D Tantalum
Nichicon PF and PL Aluminum electrolytic
Mallory TDC and TDL Tantalum
TOKIN MLCC Multilayer ceramic
Murata GRM Multilayer ceramic
Data Sheet ADP3605
Rev. B | Page 5 of 12
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No. Mnemonic Description
1 C
P
+ Positive Terminal for the Pump Capacitor.
2 GND Device Ground.
3 C
P
Negative Terminal for the Pump Capacitor.
4 SD Logic Level Shutdown Pin. Apply logic high or connect to V
IN
to shut down the device. In shutdown mode, the
charge pump is turned off, and the quiescent current is reduced to 2 µA (typical). Apply a logic low or connect to
ground for normal operation.
5 V
SENSE
Output Voltage Sense Line. Connect a resistor between this pin and V
OUT
to set the desired output voltage.
6 NC No Connect. Do not connect to this pin.
7 V
OUT
Regulated Negative Output Voltage. Connect a low ESR, 4.7 µF or larger, capacitor between this pin and the
device ground.
8 V
IN
Positive Supply Input Voltage. Connect a low ESR bypass capacitor between this pin and the device ground to
minimize supply transients.
C
P
+
1
GND
2
C
P
3
SD
4
V
IN
8
V
OUT
7
NC
6
V
SENSE
5
NOTES
1. NC = NO CONNECT. DO NOT
CONNECT TO THIS PIN.
ADP3605
TOP VIEW
(Not to Scale)
11135-003

ADP3605ARZ-R7

Mfr. #:
Manufacturer:
Analog Devices / Linear Technology
Description:
Switching Voltage Regulators 120mA Switched Capacitor VTG Invrtr
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet