Data Sheet AD622
Rev. E | Page 3 of 16
SPECIFICATIONS
T
A
= 25°C, V
S
= ±15 V, and R
L
= 2 kΩ typical, unless otherwise noted.
Table 2.
Parameter Conditions Min Typ Max Unit
GAIN G = 1 + (50.5 k/R
G
)
Gain Range
1
1000
Gain Error
1
V
OUT
= ±10 V
G = 1 0.05 0.15 %
G = 10 0.2 0.50 %
G = 100 0.2 0.50 %
G = 1000
0.2
0.50
%
Nonlinearity V
OUT
= ±10 V
G = 1 to 1000 R
L
= 10 kΩ 10 ppm
G = 1 to 100 R
L
= 2 kΩ 10 ppm
Gain vs. Temperature Gain = 1 10 ppm/°C
Gain > 1
1
−50 ppm/°C
VOLTAGE OFFSET Total RTI Error = V
OSI
+ V
OSO
/G
Input Offset, V
OSI
V
S
= ±5 V to ±15 V 60 125 µV
Average Temperature Coefficient V
S
= ±5 V to ±15 V 1.0 µV/°C
Output Offset, V
OSO
V
S
= ±5 V to ±15 V
600
1500
µV
Average Temperature Coefficient V
S
= ±5 V to ±15 V 15 µV/°C
Offset Referred to Input vs. Supply (PSR) V
S
= ±5 V to ±15 V
G = 1 80 100 dB
G = 10 95 120 dB
G = 100
110
140
dB
G = 1000 110 140 dB
INPUT CURRENT
Input Bias Current
2.0
5.0
nA
Average Temperature Coefficient 3.0 pA/°C
Input Offset Current 0.7 2.5 nA
Average Temperature Coefficient 2.0 pA/°C
INPUT
Input Impedance
Differential 10||2 G Ω||pF
Common Mode 10||2 GΩ||pF
Input Voltage Range
2
V
S
= ±2.6 V to ±5 V
−V
S
+ 1.9
+V
S
– 1.2
V
Over Temperature −V
S
+ 2.1 +V
S
– 1.3 V
V
S
= ±5 V to ±18 V −V
S
+ 1.9 +V
S
– 1.4 V
Over Temperature −V
S
+ 2.1 +V
S
– 1.4 V
Common-Mode Rejection Ratio
DC to 60 Hz with 1 kΩ Source Imbalance
V
CM
= 0 V to ±10 V
G = 1
66
78
dB
G = 10 86 98 dB
G = 100 103 118 dB
G = 1000 103 118 dB
OUTPUT
Output Swing R
L
= 10 kΩ
V
S
= ±2.6 V to ±5 V −V
S
+ 1.1 +V
S
– 1.2 V
Over Temperature −V
S
+ 1.4 +V
S
– 1.3 V
V
S
= ±5 V to ±18 V −V
S
+ 1.2 +V
S
– 1.4 V
Over Temperature −V
S
+ 1.6 +V
S
– 1.5 V
Short Current Circuit ±18 mA
AD622 Data Sheet
Rev. E | Page 4 of 16
Parameter Conditions Min Typ Max Unit
DYNAMIC RESPONSE
Small Signal 3 dB Bandwidth
G = 1 1000 kHz
G = 10 800 kHz
G = 100
120
kHz
G = 1000 12 kHz
Slew Rate 1.2 V/µs
Settling Time to 0.1% 10 V step
G = 1 to 100 10 µs
NOISE
Voltage Noise, 1 kHz Total RTI Noise = √(e
2
ni
) + (e
no
∕G)2
Input Voltage Noise, e
ni
12 nV/Hz
Output Voltage Noise, e
no
72 nV/Hz
RTI, 0.1 Hz to 10 Hz
G = 1 4.0 µV p-p
G = 10 0.6 µV p-p
G = 100 0.3 µV p-p
Current Noise f = 1 kHz 100 fA/Hz
0.1 Hz to 10 Hz
10
pA p-p
REFERENCE INPUT
R
IN
20 kΩ
I
IN
V
IN+
, V
REF
= 0
50
60
µA
Voltage Range −V
S
+ 1.6 +V
S
– 1.6 V
Gain to Output 1 ± 0.0015
POWER SUPPLY
Operating Range
3
±2.6 ±18 V
Quiescent Current V
S
= ±2.6 V to ±18 V 0.9 1.3 mA
Over Temperature 1.1 1.5 mA
TEMPERATURE RANGE
For Specified Performance 40 to +85 °C
1
Does not include effects of External Resistor R
G
.
2
One input grounded, G = 1.
3
Defined as the same supply range that is used to specify PSR.
Data Sheet AD622
Rev. E | Page 5 of 16
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter Rating
Supply Voltage ±18 V
Internal Power Dissipation
1
650 mW
Input Voltage (Common Mode) ±V
S
Differential Input Voltage
2
±25 V
Output Short Circuit Duration Indefinite
Storage Temperature Range −65°C to +125°C
Operating Temperature Range −40°C to +85°C
Lead Temperature (Soldering, 10 sec)
300°C
1
Specification is for device in free air; see Table 4.
2
May be further restricted for gains greater than 14. See the Input Protection
section for more information.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θ
JA
is specified for the device in free air.
Table 4. Thermal Resistance
Package Type θ
JA
Unit
8-Lead PDIP (N-8) 95 °C/W
8-Lead SOIC_N (R-8) 155 °C/W
ESD CAUTION

AD622ARZ-RL

Mfr. #:
Manufacturer:
Description:
Instrumentation Amplifiers LOW COST
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union