6
LTC3736
3736fa
UU
U
PI FU CTIO S
I
TH1
/I
TH2
(Pins 1, 8/ Pins 4, 11): Current Threshold and
Error Amplifier Compensation Point. Nominal operating
range on these pins is from 0.7V to 2V. The voltage on
these pins determines the threshold of the main current
comparator.
PLLLPF (Pin 3/Pin 6): Frequency Set/PLL Lowpass Filter.
When synchronizing to an external clock, this pin serves
as the lowpass filter point for the phase-locked loop. Nor-
mally a series RC is connected between this pin and ground.
When not synchronizing to an external clock, this pin serves
as the frequency select input. Tying this pin to GND selects
300kHz operation; tying this pin to V
IN
selects 750kHz op-
eration. Floating this pin selects 550kHz operation.
SGND (Pin 4/Pin 7): Small-Signal Ground. This pin serves
as the ground connection for most internal circuits.
V
IN
(Pin 5/Pin 8): Chip Signal Power Supply. This pin
powers the entire chip except for the gate drivers. Externally
filtering this pin with a lowpass RC network (e.g.,
R = 10Ω, C = 1µF) is suggested to minimize noise pickup,
especially in high load current applications.
TRACK (Pin 6/Pin 9): Tracking Input for Second Control-
ler. Allows the start-up of V
OUT2
to “track” that of V
OUT1
according to a ratio established by a resistor divider on
V
OUT1
connected to the TRACK pin. For one-to-one track-
ing of V
OUT1
and V
OUT2
during start-up, a resistor divider
(UF/GN Package)
with values equal to those connected to V
FB2
from V
OUT2
should be used to connect to TRACK from V
OUT1
.
PGOOD(Pin 9/Pin 12): Power Good Output Voltage Moni-
tor Open-Drain Logic Output. This pin is pulled to ground
when the voltage on either feedback pin (V
FB1
, V
FB2
) is not
within ±13.3% of its nominal set point.
PGND (Pins 12, 16, 20, 25/ Pins 15, 19, 23): Power
Ground. These pins serve as the ground connection for the
gate drivers and the negative input to the reverse current
comparators. The Exposed Pad (UF package) must be
soldered to PCB ground.
RUN/SS (Pin 14/Pin 17): Run Control Input and Optional
External Soft-Start Input. Forcing this pin below 0.65V shuts
down the chip (both channels). Driving this pin to V
IN
or
releasing this pin enables the chip, using the chip’s inter-
nal soft-start. An external soft-start can be programmed by
connecting a capacitor between this pin and ground.
TG1/TG2 (Pins 17, 15/Pins 20, 18): Top (PMOS) Gate Drive
Output. These pins drive the gates of the external P-channel
MOSFETs. These pins have an output swing from PGND to
SENSE
+
.
SYNC/FCB (Pin 18/Pin 21): This pin performs three
functions: 1) auxiliary winding feedback input, 2) external
clock synchronization input for phase-locked loop, and 3)
Burst Mode operation or forced continuous mode select.
Shutdown Quiescent Current
vs Input Voltage
INPUT VOLTAGE (V)
2
0
SHUTDOWN CURRENT (µA)
2
6
8
10
20
14
4
6
7
3736 G17
4
16
18
12
35
8
9
10
RUN/SS = 0V
RUN/SS Start-Up Current
vs Input Voltage
INPUT VOLTAGE (V)
2
RUN/SS PIN PULL-UP CURRENT (µA)
0.5
0.6
0.7
10
3736 G18
0.4
0.3
0
0.1
4
6
8
3
5
7
9
0.2
0.9
0.8
RUN/SS = 0V
TYPICAL PERFOR A CE CHARACTERISTICS
UW
T
A
= 25°C unless otherwise noted.
