OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AT30TS75-MA8-T

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P37
AT30TS75 [DATASHEET]
Atmel-8748E-DTS-AT30TS75-Datasheet_092013
34
11.3 8MA2 — 8-pad UDFN
TITLE
DRAWING NO. GPC
REV.
Package Drawing Contact:
packagedrawings@atmel.com
8MA2YNZ B
8MA2, 8-pad, 2 x 3 x 0.6 mm Body, Thermally
Enhanced Plastic Ultra Thin Dual Flat No
Lead Package (UDFN)
COMMON DIMENSIONS
(Unit of Measure = mm)
SYMBOL
MIN
NOM
MAX
NOTE
D 2.00 BSC
E 3.00 BSC
D2 1.40 1.50 1.60
E2 1.20 1.30 1.40
A 0.50 0.55 0.60
A1 0.0 0.02 0.05
A2 – – 0.55
C 0.152 REF
L 0.30 0.35 0.40
e 0.50 BSC
b 0.18 0.25 0.30 3
K 0.20 – –
7/15/11
D2
E2
E
e (6x)
L (8x)
b (8x)
Pin#1 ID
A
A1
A2
Pin 1 ID
D
C
K
8
7
6
5
1
2
3
4
1
2
3
4
8
7
6
5
35
AT30TS75 [DATASHEET]
Atmel-8748E-DTS-AT30TS75-Datasheet_092013
12. Errata
Issue: The internal fault counter will be reset when updating the Configuration Register, the T
HIGH
Limit Register, or the T
LOW
Limit Register.
Workaround: None. The current version of the device was intentionally designed to operate this way; however,
it has been discovered that resetting of the fault counter when updating the registers is not
preferred.
Resolution: The operation of the device will be changed with a new revision of the device (AT30TS75A) so
updating the Configuration Register, the T
HIGH
Limit Register, or the T
LOW
Limit Register will not
affect the internal fault counter. See the AT30TS75A datasheet.
12.1 ALERT Pin
Issue: Depending on Power supply Ramp time, the ALERT pin may not be configured in the
proper state to be a true open drain.
Workaround: The ALERT pin must be pulled-high using an external pull-up resistor even when it is not used.
Care must also be taken to prevent this pin from being shorted directly to ground without a resistor
at any time whether during testing or normal operation.
Resolution: The operation of the ALERT Pin will be changed with a new revision (AT30TS75A) of the device
so it is a true open drain. See the AT30TS75A datasheet.
12.2 ALERT Pin State
Issue: When switching between Comparator and Interrupt modes (or vice versa) while the ALERT
pin is active, the device will not retain its active alert state and will automatically deassert
the ALERT pin.
Workaround: None.
Resolution: The operation of the ALERT pin will be changed with a new revision of the device (AT30TS75A) so
it will properly retain the ALERT pin status when switching modes. See the AT30TS75A datasheet.
AT30TS75 [DATASHEET]
Atmel-8748E-DTS-AT30TS75-Datasheet_092013
36
13. Revision History
Doc. Rev. Date Comments
8748E
04/2014 End Of Life. Replaced by AT30TS74 and AT30TS75A.
09/2013
Update I
CC
parameter in the DC Characteristics table.
Update Absolute Maximum Ratings section.
Update the temperature accuracy and ranges.
Increase t
V
HS mode maximum from 50 to 80ns.
Update Power-up timing table.
Update the errata section.
8748D 07/2013
Updated errata section.
Update footers and disclaimer page.
8748C 06/2012
Add t
PU
Power-Up condition.
Update Atmel logos and disclaimer pager.
8748B 04/2012
Update alert pin’s function description and errata.
Update Power-up Timing figure.
Add device operation temperatures (–40°C to +125°C) accuracy guaranteed.
Add sensor accuracy typical ±3.0 and remove value from max.
Correct Clock High Time max value from 40KHz to 400KHz.
Change 45A to 75A for low power dissipation typical active current.
Change 0.1A to 1A for Shutdown mode typical active current.
Change 200 to 500 for POR Time max value.
Remove preliminary status.
Update template.
8748A 03/2011 Inital document release.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P30P31-P33P34-P36P37-P37

AT30TS75-MA8-T

Mfr. #:
Buy AT30TS75-MA8-T
Manufacturer:
Description:
Board Mount Temperature Sensors TMP SENSOR
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet