4
FN6111.3
February 5, 2008
Total Harmonic Distortion f = 20Hz to 20kHz, V
COM
= 2V
PP
, R
L
= 600Ω 25 - 0.003 - %
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 106 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 212 - pF
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 1.65 - 4.5 V
Positive Supply Current, I+ V+ = +4.5V, V
IN
= 0V or V+ 25 - - 0.09 μA
Full - - 1.4 μA
Positive Supply Current, I+ V+ = +4.2V, V
IN
= 2.85V 25 - - 12 μA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full - - 0.5 V
Input Voltage High, V
INH
Full 1.6 - - V
Input Current, I
INH
, I
INL
V+ = 4.5V, V
IN
= 0V or V+, (Note 10) Full -0.5 - 0.5 μA
NOTES:
6. V
IN
= input voltage to perform proper function.
7. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
8. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
9. Flatness is defined as the difference between maximum and minimum value of ON-Resistance over the specified analog signal range.
10. Limits established by characterization and are not production tested.
11. r
ON
matching between channels is calculated by subtracting the channel with the highest max r
ON
value from the channel with lowest max r
ON
value, between NC1 and NC2, NC3 and NC4 or between NO1 and NO2, NO3 and NO4.
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Note 6),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 7, 8) TYP
MAX
(Notes 7, 8) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON-Resistance, r
ON
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
(See Figure 5)
25 - 0.3 0.45 Ω
Full - - 0.6 Ω
r
ON
Matching Between Channels,
Δr
ON
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= Voltage at
max r
ON
, (Note 11)
25 - 0.04 0.08 Ω
Full - - 0.09 Ω
r
ON
Flatness, r
FLAT(ON)
V+ = 2.7V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
(Note 9)
25 - 0.06 0.15 Ω
Full - - 0.15 Ω
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 3.3V, V
COM
= 0.3V, 3V, V
NO
or V
NC
= 3V, 0.3V 25 - 1.2 - nA
Full - 13 - nA
COM ON Leakage Current,
I
COM(ON)
V+ = 3.3V, V
COM
= 0.3V, 3V, or V
NO
or V
NC
= 0.3V,
3V, or Floating
25 - 1 - nA
Full - 35 - nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 2.7V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω,
C
L
= 35pF, (See Figure 1, Note 10)
25 - 21 30 ns
Full - - 35 ns
Turn-OFF Time, t
OFF
V+ = 2.7V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω,
C
L
= 35pF, (See Figure 1, Note 10)
25 - 17 27 ns
Full - - 32 ns
Break-Before-Make Time Delay, t
D
V+ = 3.3V, V
NO
or V
NC
= 1.5V, R
L
= 50Ω,
C
L
= 35pF, (See Figure 3, Note 10)
Full 2 3 - ns
Electrical Specifications - 4.3V Supply Test Conditions: V+ = +3.9V to +4.5V, GND = 0V, V
INH
= 1.6V, V
INL
= 0.5V (Note 6),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 7, 8) TYP
MAX
(Notes 7, 8) UNITS
ISL8499
