OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

6N139-X007T

P1-P3P4-P6P7-P9
6N138, 6N139
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 23-Jan-15
1
Document Number: 83605
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
High Speed Optocoupler, 100 kBd, Low Input Current,
Photodiode Darlington Output
DESCRIPTION
High common mode transient immunity and very high
current ratio together with 5300 V
RMS
insulation are
achieved by coupling and LED with an integrated high gain
photo detector in an eight pin dual-in-line package.
Separate pins for the photo diode and output stage enable
TTL compatible saturation voltages with high speed
operation.
Access to the base terminal allows adjustment to the gain
bandwidth.
The 6N138 is ideal for TTL applications since the 300 %
minimum current transfer ratio with an LED current of
1.6 mA enables operation with one unit load-in and one unit
load-out with a 2.2 kΩ pull-up resistor.
The 6N139 is best suited for low power logic applications
involving CMOS and low power TTL. A 400 % current
transfer ratio with only 0.5 mA of LED current is guaranteed
from 0 °C to 70 °C.
Caution: Due to the small geometries of this device, it should be
handled with Electrostatic Discharge (ESD) precautions. Proper
grounding would prevent damage further and/or degradation which
may be induced by ESD.
FEATURES
• High current transfer ratio, 300 %
• Low input current, 0.5 mA
• High output current, 60 mA
• Isolation test voltage, 5300 V
RMS
• TTL compatible output, V
OL
= 0.1 V
• High common mode rejection, 500 V/μs
• Adjustable bandwidth-access to base
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
APPLICATIONS
• Microprocessor system interface
• PLC, ATE input / output isolation
• EIA RS232 line receiver
• TTL, CMOS voltage level translation
• Multiplexed data transmission
• Digital control power supply
• Ground loop and electrical noise elimination
AGENCY APPROVALS
• UL1577, file no. E52744, double protection
• DIN EN 60747-5-5 available with option 1
Note
• For additional information on the available options refer to option information.
1
2
3
4
8
7
6
5
V
CC
V
B
V
O
GND
NC
A
C
NC
ORDERING INFORMATION
6N13#-X0##T
PART NUMBER PACKAGE OPTION TAPE
AND
REEL
AGENCY CERTIFIED/PACKAGE
CTR (%)
1.6 mA
UL > 300 > 500
DIP-8 6N138 6N139, 6N139-X001
SMD-8, option 7 6N138-X007T 6N139-X007, 6N139-X007T
SMD-8, option 9 6N138-X009T 6N139-X009, 6N139-X009T
VDE > 300 > 500
SMD-8, option 7 - 6N139-X017T
SMD-8, option 9 - 6N139-X019T
> 0.1 mm
> 0.7 mm
7.62 mm
DIP
Option 7
Option 9
6N138, 6N139
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 23-Jan-15
2
Document Number: 83605
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1)
Derate linearly above 50 °C free-air temperature at a rate of 0.333 mA/°C.
(2)
Derate linearly above 50 °C free-air temperature at a rate of 0.467 mW/°C.
(3)
Derate linearly above 25 °C free-air temperature at a rate of 0.6 mA/°C.
(4)
Derate linearly above 25 °C free-air temperature at a rate of 1 mW/°C.
(5)
Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
ABSOLUTE MAXIMUM RATINGS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION PART SYMBOL VALUE UNIT
INPUT
Reverse voltage V
R
5V
Forward current I
F
25 mA
Average input current
(1)
I
f(avg)
20 mA
Input power dissipation
(2)
P
diss
35 mW
OUTPUT
Supply and output voltage
Pin 8 to 5, pin 6 to 5 6N138 V
CC
, V
O
-0.5 to 7 V
Pin 8 to 5, pin 6 to 5 6N139 V
CC
, V
O
-0.5 to 18 V
Emitter base reverse voltage Pin 5 to 7 0.5 V
Peak input current
50 % duty cycle - 1 ms
pulse width
40 mA
Peak transient input current t
p
≤ 1 μs, 300 pps 1 A
Output current Pin 6 I
O
60 mA
Output power dissipation
(3)(4)
P
diss
100 mW
COUPLER
Isolation test voltage t = 1 min V
ISO
5300 V
RMS
Isolation resistance
V
IO
= 500 V, T
amb
= 25 ° C R
IO
≥ 10
12
Ω
V
IO
= 500 V, T
amb
= 100 ° C R
IO
≥ 10
11
Ω
Storage temperature T
stg
-55 to +150 °C
Operating temperature T
amb
-55 to +100 °C
Lead soldering temperature
(5)
t = 10 s T
sld
260 °C
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
INPUT
Input forward voltage I
F
= 1.6 mA V
F
1.4 1.7 V
Input reverse breakdown voltage I
R
= 10 μA B
VR
5V
Temperature coefficient of
forward voltage
I
F
= 1.6 mA -1.8 mV/°C
OUTPUT
Logic low, output voltage
(1)
I
F
= 1.6 mA, I
O
= 4.8 mA, V
CC
= 4.5 V 6N138 V
OL
0.1 0.4 V
I
F
= 1.6 mA, I
O
= 8 mA, V
CC
= 4.5 V 6N139 V
OL
0.1 0.4 V
I
F
= 5 mA, I
O
= 15 mA, V
CC
= 4.5 V 6N139 V
OL
0.15 0.4 V
I
F
= 12 mA, I
O
= 24 mA, V
CC
= 4.5 V 6N139 V
OL
0.25 0.4 V
Logic high, output current
(1)
I
F
= 0 mA, V
CC
= 7 V 6N138 I
OH
0.1 250 μA
I
F
= 0 mA, V
CC
= 18 V 6N139 I
OH
0.05 100 μA
Logic low supply current
(1)
I
F
= 1.6 mA, V
O
= OPEN, V
CC
= 18 V I
CCL
0.2 1.5 mA
Logic high supply current
(1)
I
F
= 0 mA, V
O
= OPEN, V
CC
= 18 V I
CCH
0.001 10 μA
6N138, 6N139
www.vishay.com
Vishay Semiconductors
Rev. 1.6, 23-Jan-15
3
Document Number: 83605
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
(1)
Pin 7 open.
(2)
Device considered a two-terminal device: pins 1, 2, 3 and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
Notes
(1)
DC current transfer ratio is defined as the ratio of output collector current, I
O
, to the forward LED input current, I
F
times 100 %.
(2)
Pin 7 open.
Note
• As per IEC 60747-5-2, §7.4.3.8.1, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with
the safety ratings shall be ensured by means of protective circuits.
Note
(1)
Using a resistor between pin 5 and 7 will decrease gain and delay time.
COUPLER
Input capacitance f = 1 MHz, V
F
= 0 C
IN
25 pF
Input output insulation leakage
current
(2)
45 % relative humidity,
T
amb
= 25 °C, t = 5 s, V
IO
= 3000 V
DC
1μA
Resistance (input to output)
(2)
V = 500 V
peak
R
IO
10
12
Ω
Capacitance (input to output)
(2)
f = 1 MHz C
IO
0.6 pF
CURRENT TRANSFER RATIO
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
Current transfer ratio
(1)(2)
I
F
= 1.6 mA, V
O
= 0.4 V, V
CC
= 4.5 V 6N138 CTR 300 1600 %
Current transfer ratio
I
F
= 0.5 mA, V
O
= 0.4 V, V
CC
= 4.5 V 6N139 CTR 400 1600 %
I
F
= 1.6 mA, V
O
= 0.4 V, V
CC
= 4.5 V 6N139 CTR 500 2000 %
SAFETY AND INSULATION RATINGS
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Climatic classification according to IEC 68 part 1 55/100/21
Comparative tracking index CTI 175 399
V
IOTM
8000 V
V
IORM
890 V
P
SO
500 mW
I
SI
300 mA
T
SI
175 °C
Creepage distance Standard DIP-8 8 mm
Clearance distance Standard DIP-8 7 mm
Creepage distance 400 mil DIP-8 8 mm
Clearance distance 400 mil DIP-8 8 mm
SWITCHING CHARACTERISTICS
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
Propagation delay time to logic
low at output
I
F
= 1.6 mA, R
L
= 2.2 kΩ 6N138 t
PHL
210μs
Propagation delay time to logic
low at output
(1)(2)
I
F
= 0.5 mA, R
L
= 4.7 kΩ 6N139 t
PHL
625μs
I
F
= 12 mA, R
L
= 270 Ω 6N139 t
PHL
0.6 1 μs
Propagation delay time to logic
high at output
I
F
= 1.6 mA, R
L
= 2.2 kΩ 6N138 t
PLH
235μs
I
F
= 0.5 mA, R
L
= 4.7 kΩ 6N139 t
PLH
460μs
Propagation delay time to logic
high at output
(1)
I
F
= 12 mA, R
L
= 270 Ω 6N139 t
PLH
1.5 7 μs
ELECTRICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT
P1-P3P4-P6P7-P9

6N139-X007T

Mfr. #:
Buy 6N139-X007T
Manufacturer:
Vishay Semiconductors
Description:
High Speed Optocouplers H. Speed 100MBd CTR>300%
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet