MC100LVEP05
http://onsemi.com
5
Table 7. 100EP DC CHARACTERISTICS, NECL V
CC
= 0 V, V
EE
= −2.375 V to −3.6 V (Note 10)
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 15 25 32 17 27 36 19 28 38 mA
V
OH
Output HIGH Voltage (Note 11) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
V
OL
Output LOW Voltage (Note 11) −1945 −1770 −1600 −1945 −1770 −1600 −1945 −1770 −1600 mV
V
IH
Input HIGH Voltage (Single−Ended) −1165 −880 −1165 −880 −1165 −880 mV
V
IL
Input LOW Voltage (Single−Ended) −1945 −1600 −1945 −1600 −1945 −1600 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 12)
V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current D
D
0.5
−150
0.5
−150
0.5
−150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
10.Input and output parameters vary 1:1 with V
CC
.
11. All loading with 50 W to V
CC
− 2.0 V.
12.V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
Table 8. AC CHARACTERISTICS V
CC
= 0 V; V
EE
= −2.375 V to −3.6 V or V
CC
= 2.375 V to 3.6 V; V
EE
= 0 V (Note 13)
Symbol Characteristic
−40°C 25°C 85°C
Unit
Min Typ Max Min Typ Max Min Typ Max
f
max
Maximum Frequency
(Figure 2)
3.0 3.0 3.0 GHz
t
PLH
,
t
PHL
Propagation Delay to
Output Differential
160 210 260 170 220 270 210 260 320 ps
t
JITTER
RMS Random Clock Jitter f
in
3.0 GHz
(Figure 2)
0.2 1 0.2 1 0.2 1.5 ps
V
PP
Input Voltage Swing (Differential Config-
uration)
150 800 1200 150 800 1200 150 800 1200 mV
t
r
t
f
Output Rise/Fall Times Q
(20% − 80%)
70 120 170 80 130 180 100 150 200 ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
13.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to V
CC
− 2.0 V.
