OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

334-15/X2C3-1PSA

P1-P3P4-P6P7-P9P10-P12
Technical Data Sheet
334-15/X2C3-1PSA
Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 10 of 12
Device Number:
DLE-0000702
Established date:01-06-2009 Established by: Ruby Lin
Prehead
laminar wave
Fluxing
Avoiding applying any stress to the lead frame while the LEDs are at high temperature
particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or
vibration until the LEDs return to room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak
temperature.
Although the recommended soldering conditions are specified in the above table, dip or
handsoldering at the lowest possible temperature is desirable for the LEDs.
Wave soldering parameter must be set and maintain according to recommended temperature
and dwell time in the solder wave.
4. Cleaning
When necessary, cleaning should occur only with isopropyl alcohol at room temperature for
a duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of
ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the
assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause
damage to the LED.
Technical Data Sheet
334-15/X2C3-1PSA
Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 11 of 12
Device Number:
DLE-0000702
Established date:01-06-2009 Established by: Ruby Lin
5. Circuit Protection
Below the zener reference voltage Vz, all the current flows through LED and as the voltage
rises to Vz, the zener diode “breakdown." If the voltage tries to rise above Vz current flows
through the zener branch to keep the voltage at exactly Vz.
When the LED is connected using serial circuit, if either piece of LED is no light up but
current can’t flow through causing others to light down. In new design, the LED is parallel
with zener diode. if either piece of LED is no light up but current can flow through causing
others to light up.
6. Heat Management
Heat management of LEDs must be taken into consideration during the design stage of LED
application. The current should be de-rated appropriately by referring to the de-rating curve
found in each product specification.
The temperature surrounding the LED in the application should be controlled. Please refer to
the data sheet de-rating curve.
Technical Data Sheet
334-15/X2C3-1PSA
Everlight Electronics Co., Ltd. http\\:www.everlight.com Rev 1 Page: 12 of 12
Device Number:
DLE-0000702
Established date:01-06-2009 Established by: Ruby Lin
7. ESD (Electrostatic Discharge)
Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.
An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling
LEDs.
All devices, equipment and machinery must be properly grounded.
Use ion
blower to neutralize the static charge which might have built up on surface of the
LEDs plastic le
ns as a result of friction between LEDs during storage and handing.
8. Other
Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http:\\www.everlight.com
P1-P3P4-P6P7-P9P10-P12

334-15/X2C3-1PSA

Mfr. #:
Buy 334-15/X2C3-1PSA
Manufacturer:
Description:
Standard LEDs - Through Hole 5mm LED
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet