BH□□RB1WGUT series
Technical Note
2/8
www.rohm.com
2011.01 - Rev.C
© 2011 ROHM Co., Ltd. All rights reserved.
●Absolute maximum ratings
Parameter
Symbol Ratings Unit
Applied supply voltage
VMAX -0.3 to +6.5 V
Power dissipation
Pd 530
*1
mW
Operating temperature range
Topr -40 to +85 °C
Storage temperature range
Tstg -55 to +125 °C
*1: Reduce by 5.3 mW/C over 25C, when mounted on a glass epoxy PCB (7 mm 7 mm 0.8 mm).
●Recommended operating ranges (not to exceed Pd)
Parameter
Symbol Ratings Unit
Power supply voltage
V
IN 2.5 to 5.5 V
Output current
IOUT 0 to 150 mA
●Recommended operating conditions
Parameter
Symbol
Ratings
Unit
Conditions
Min. Typ. Max.
Input capacitor CIN 0.7
*2
1.0 — µF
The use of ceramic capacitors is
recommended.
Output capacitor CO 0.7
*2
1.0 — µF
The use of ceramic capacitors is
recommended.
*2: Make sure that the output capacitor value is not kept lower than this specified level across a variety of temperature, DC bias characteristic.
And also make sure that the capacitor value cannot change as time progresses.
●Electrical characteristics
(Unless otherwise specified, Ta = 25°C, V
IN = VOUT + 1.0 V
*5
, STBY = 1.5 V, CIN = 1 µF, CO = 1 µF)
Parameter
Symbol
Limits
Unit
Conditions
Min. Typ. Max.
Output voltage 1 VOUT1
V
OUT
0.99
V
OUT
VOUT
1.01
V
IOUT = 1 mA, Ta = 25°C,
BH25RB1WGUT or higher
VOUT
- 25 mV
VOUT
+ 25 mV
I
OUT = 1mA, Ta = 25°C,
BH15, 18RB1WGUT
Output voltage 2 VOUT2
V
OUT
0.97
V
OUT
VOUT
1.03
V
IOUT = 1 mA
Ta = -40°C to 85°C
*3
Circuit current IGND — 34 72 µA
I
OUT = 0 mA
Ta = -40°C to 85°C
*3
Circuit current (STBY) ICCST — — 1.0 µA STBY = 0 V
Ripple rejection ratio RR — 63 — dB
VRR = -20 dBV, fRR = 1 kHz,
I
OUT = 10 mA
Dropout voltage VSAT — 100 150 mV
VIN = 0.98 VOUT, IOUT = 100 mA
(Excluding BH15, 18RB1WGUT)
Line regulation VDLI — 2 20 mV
I
OUT = 10 mA
V
IN = VOUT + 0.5 V to 5.5 V
*4
Load regulation VDLO — 2 30 mV IOUT = 1 mA to 100 mA
Overcurrent protection limit current ILMAX — 300 — mA VO = VOUT 0.98
Short current ISHORT — 40 — mA VO = 0 V
STBY pin current ISTBY 0.5 1.3 3.6 µA Ta = -40°C to 85°C
*3
STBY control voltage
ON VSTBH 1.2 — VIN V Ta = -40°C to 85°C
*3
OFF VSTBL -0.2 — 0.2 V Ta = -40°C to 85°C
*3
* This IC is not designed to be radiation-resistant.
*3: These specifications are guaranteed by design.
*4: For BH15, 18RB1WGUT, VIN = 3.0 V to 5.5 V.
*5: For BH15, 18RB1WGUT, VIN = 3.5 V.