MC100EP16VS
http://onsemi.com
6
Table 6. DC CHARACTERISTICS, NECL V
CC
= 0 V; V
EE
= −5.5 V to −3.0 V (Note 9)
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 30 36 42 31 38 44 32 40 48 mA
V
OH
Output HIGH Voltage (Note 10)
V
CC
> V
CTRL
> V
EE
−1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV
V
OL
Output LOW Voltage (Max Swing)
(Note 10) V
CTRL
≤ V
BB
−1945 −1810 −1695 −1945 −1780 −1695 −1945 −1780 −1695
mV
VCC ≥ V
CTRL
> V
BB
See
Fig.2
See
Fig.2
See
Fig.2
V
CTRL
= V
CC
(Min Swing) −1195 −1070 −945 −1205 −1080 −955 −1235 −1110 −985
V
IH
D, D Input HIGH Voltage (Single−Ended) −1225 −880 −1225 −880 −1225 −880 mV
V
IL
D, D Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV
V
BB
Output Voltage Reference −1525 −1425 −1325 −1525 −1425 −1325 −1525 −1425 −1325 mV
V
CTRL
Input Voltage (V
CTRL
) V
EE
V
CC
V
EE
V
CC
V
EE
V
CC
mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 11)
V
EE
+2.0 −0.4 V
EE
+2.0 −0.4 V
EE
+2.0 −0.4 V
I
IH
Input HIGH Current 150 150 150
A
I
IL
Input LOW Current D
D
0.5
−150
0.5
−150
0.5
−150
A
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
9. Input and output parameters vary 1:1 with V
CC
.
10.All loading with 50 to V
CC
− 2.0 V. V
OH
does not change with V
CTRL
. V
OL
changes with V
CTRL
. V
CTRL
is referenced to V
CC
.
11. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
Table 7. AC CHARACTERISTICS V
CC
= 0 V; V
EE
= −3.0 V to −5.5 V or V
CC
= 3.0 V to 5.5 V; V
EE
= 0 V (Note 12)
−40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
f
max
Maximum Toggle Frequency
(See Figure 6. F
max
/JITTER)
> 4 > 4 > 4 GHz
t
PLH
,
t
PHL
Propagation Delay to Output Differential
Max Swing
Min Swing
150
90
220
150
280
210
150
90
220
150
280
210
160
100
240
160
300
220
ps
t
SKEW
Duty Cycle Skew (Note 13) 5.0 20 5.0 20 5.0 20 ps
t
JITTER
Cycle−to−Cycle Jitter
(See Figure 6. F
max
/JITTER)
0.2 < 1 0.2 < 1 0.2 < 1 ps
V
PP
Input Voltage Swing
(Differential Configuration) (Note 14)
150 800 1200 150 800 1200 150 800 1200 mV
t
r
t
f
Output Rise/Fall Times Max Swing Q
(20% − 80%) Min Swing
70
30
120
80
170
130
80
20
130
70
180
120
100
20
150
70
200
120
ps
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
12.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 to V
CC
− 2.0 V.
13.Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays
are measured from the cross point of the inputs to the cross point of the outputs.
14.V
PP
(min) is minimum input swing for which AC parameters are guaranteed.
