OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MDF76URW-30S-1H(55)

P1-P3P4-P6P7-P9P10-P12
7
MDF76 Series●1.0 mm Pitch, Board-to-Wire LCD Interface Connectors
(1)
40.65±0.1
1.2±0.1
P=1±0.03
29±0.05
31±0.05
37.65±0.05
(0.3)
(0.5)
1.5±0.1
3±0.1
2.2±0.05
0.5±0.05
0.8±0.08
1±0.1
3.5±0.05
0.6±0.05
No.1(Ground) (Note)
Note: For MDF76LBRW, MDF76URW, No.32 (Ground and No. 31 (Signal) are on left side.
No.2(Signal) (Note)
No.31(Signal)
No.32
(Ground)
Gold plated
■Receptacles (High profile)
●Right angle, Standard, top board, SMT
■Recommended PCB mounting pattern
●Mid-mount
Contact pitch = 1
1.3
29
3.45
2.35
No.1 (Ground)
0.4
Lead pitch=1
No.2 (Signal)
31
No.32 (Ground)
No.31 (Signal)
1.2
0.8
3.25
37.35
40.05
0.4
Insulator Color Packaging
Above the mounting surface
Beige 2,500 pcs. / reel 2.35 mm
Part Number CL No. Number of contacts RoHS
MDF76GW-30S-1H(55) 547-0916-6-55 30 YES
For receptacles:
MDF76KBW-30S-1H(**)
MDF76LBRW-30S-1H(**)
MDF76TW-30S-1H(**)
MDF76URW-30S-1H(**)
P=1±0.05
31±0.05
0.8±0.1
0.6±0.05
No.1(Ground)
No.2(Signal)
No conductive traces
No.31(Signal)
No.32
(Ground)
36.85±0.1
1.8±0.1
(40.45)
1.8±0.1
3.25±0.1
1.5±0.05
(3.9)
(37.35±0.3)
0.3±0.15
●Top board
For receptacles:
MDF76GW-30S-1H(**)
All dimensions: mm
All dimensions: mm
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
Apr.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
MDF76 Series●1.0 mm Pitch, Board-to-Wire LCD Interface Connectors
8
A-A
Ø1.5
+0.1
0
1.95
12
2
4
1.75
26.2
52.4
56
(2)R0.75
0.2
A
A
(42)
0.4
2.95
A
A
Unreeling direction
Ø13
(Ø80)
(Ø380)
(56.5) (1.6)
Part Number Label
Unreeling direction
■Packaging Specifications
◆
MDF76TW-30S-1H(55)
MDF76URW-30S-1H(55)
MDF76GW-30S-1H(55)
1.8
12
2
4
Ø1.5
t=0.4
2.3
(42)
(2)
R0.75
0.2
Ø13
(Ø80)
(Ø380)
(56.5) (2)
1.75
26.2
52.4
56
A
A
A-A
Part Number Label
Unreeling direction
Unreeling direction
◆
MDF76KBW-30S-1H(55)
MDF76LBRW-30S-1H(55)
All dimensions: mm
All dimensions: mm
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
Apr.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
9
MDF76 Series●1.0 mm Pitch, Board-to-Wire LCD Interface Connectors
BUsage Recommendations
Refer to “Nylon Connector Use Handbook”.
The crimp contact termination must be performed using specified tools.
All dimensions and crimp conditions are listed in applicable Crimp
Condition Table and Crimping Quality Standards Manual.
■ Insert the contact retention tool in the insulator body and carefully lift the
molded-in retention tab while pulling on the wire at the same time (Fig. 1).
Do not deflect the molded-in retention tab more than is needed to release
the contact. The tab should return to its initial position after the contact is
removed.
Note: If the tab is not returning to it’s initial position carefully push I back
before inserting the crimped contact.
Permanent breakage of the molded-in retention tab will require
replacement of the entire plug.
Refer to "Nylon Connector Use Handbook".
Maximum of 0.03 mm at the connector center, with both ends of the
connector as reference points.
Thickness: 0.15 mm
Open area ratio: 100%
300±10ç for 3 seconds
Note 1: Up to 2 cycles of Reflow soldering is possible under the same
conditions, provided that there is a return to normal
temperature between the first and second cycle.
Note 2: The temperature profile indicates the board surface
temperature at the point of contacts with the connector
terminals.
10sMAX
30~60sec
255çMAX
180ç
100
150
200
250
220ç
Time (Seconds)
Temperature (ç)
60~120sec
1.Recommended temperature profile
2.Recommended manual soldering
3.Recommended screen thickness and open
area ratio
4.Board warpage
5.Cleaning conditions
6.Wire preparation and contact crimping
7.Crimped contact extraction
Contact extraction tool
Molded-in contact retention tab
Pull-out
Figure 1. Contact Extraction
Plug
Contact
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.
Apr.1.2017 Copyright 2017 HIROSE ELECTRIC CO., LTD. All Rights Reserved.
P1-P3P4-P6P7-P9P10-P12

MDF76URW-30S-1H(55)

Mfr. #:
Buy MDF76URW-30S-1H(55)
Manufacturer:
Hirose Electric
Description:
Board to Board & Mezzanine Connectors 30P R/A SMT RECEPT 1MM PITCH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet