2. Specifications
Most specification parameters for the modules are specified in the chip datasheet - JN-DS- JN5139 Wireless
Microcontroller Datasheet
, [2]. Where there are differences, the parameters are defined here.
VDD=3.0V @ +25°C
Typical DC Characteristics Notes
JN5139-xxx-
M00/01/03
JN5139-xxx-
M02/04
Deep sleep current 1.3uA 1.3uA
Sleep current 2.6uA 2.6uA With active sleep timer
Radio transmit current 37mA 125mA CPU in doze, radio transmitting
Radio receive current 37mA 45mA CPU in doze, radio receiving
Additional +/-15ppm allowance for
temperature and ageing
Centre frequency accuracy +/-25ppm +/-25ppm
Typical RF Characteristics Notes
Nominal for 1% PER, as per
802.15.4 section 6.5.3.3 (Note 1)
Receive sensitivity -96dBm -102dBm
Maximum Transmit power +1dBm 17.5dBm Nominal (Note 1)
Maximum Transmit power [Boost Mode] +2.5dBm N/A (Note 1)
Transmit power at 3.6V 19dBm With Vdd=3.6V
For 1% PER, measured as
sensitivity
Maximum input signal +10dBm +10dBm
-95 to -10
dBm
-105 to -20
dBm
RSSI range
RF Port impedance – SMA/uFl connector 50 ohm 50 ohm 2.4 - 2.5GHz
VSWR (max) 2:1 2:1 2.4 - 2.5GHz
Peripherals Notes
Master SPI port 5 selects 3 selects 250kHz - 16MHz
9 9
Slave SPI port 250kHz - 8MHz
9 9
Two UARTs 16550 compatible
Two-wire serial I/F (compatible with SMbus & I
2
9 9
C) Up to 400kHz
9 9
Two programmable Timer/Counters with
capture/compare facility, Tick timer
16MHz clock
9 9
Two programmable Sleep Timers 32kHz clock
Digital IO lines (multiplexed with UARTs, timers
and SPI selects)
21 19
9 9
Four channel Analogue-to-Digital converter
12-bit, up to 100ks/s
9 9
Two channel Digital-to-Analogue converter 11-bit, up to 100ks/s
9 9
Two programmable analogue comparators Ultra low power mode for sleep
9 9
Internal temperature sensor and battery monitor
The performance of all peripherals is defined in the JN-DS- JN5139 Wireless Microcontroller Datasheet [2]
Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated
antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity.
4 JN-DS-JN5139-xxx-Myy 1v6 © NXP Laboratories UK 2010
3. Product Development
Jennic supplies all the development tools and networking stacks needed to enable end product development to occur
quickly and efficiently. These are all freely available from www.nxp.com/jennic. A range of evaluation/developer kits
is also available, allowing products to be quickly breadboarded. Efficient development of software applications is
enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the
JenNet networking stack, the IEEE802.15.4 MAC and the ZigBee network stack, this package provides everything
required to develop application code and to trial it with hardware representative of the final module.
The modules can be user programmed both in development and in production using software supplied by Jennic.
They can also be supplied ready loaded with customer defined software if required. Access to the on-chip
peripherals, MAC and network stack software is provided through specific APIs. This
information is available on the
Jennic support website, together with many example applications, user guides, reference manuals and application
notes.
3.1. JN5139 Single Chip Wireless Microcontroller
The JN5139-xxx-Myy series is constructed around the JN5139 single chip wireless microcontroller, which includes
the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital peripherals.
The chip is described fully in
JN-DS- JN5139 Wireless Microcontroller Datasheet [2].
The module also includes a 1Mbit serial flash memory which holds the application code that is loaded into the
JN5139 during the boot sequence.
© NXP Laboratories UK 2010 JN-DS-JN5139-xxx-Myy 1v6 5
4. Pin Configurations
1
2
3
4
16
ADC4
DAC1
DAC2
COMP2+
COMP2-
SPICLK
SPIMISO
SPIMOSI
SPISSZ
DIO0/SPISEL1
DIO1/SPISEL2
DIO2/SPISEL3
SPISSM
SPISWP
DIO3/SPISEL4
DIO4/CTS0
DIO5/RTS0
DIO6/TXD0
DIO7/RXD0
DIO8/TIM0GT
DIO9/TIM0_CAP
DIO10/TIM0_OUT
DIO11/TIM1GT
VDD
GND
VSSA
ADC3
ADC2
ADC1
DIO20/RXD1
DIO19/TXD1
DIO18/RTS1
DIO17/CTS1
DIO16
DIO15/SIF_D
RESETN
DIO14/SIF_CLK
DIO13/TIM1_OUT
DIO12/TIM1_CAP
5
6
7
8
9
10
11
12
13
14
15
17 18 19 20 21 22 23 24 25 26
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
Antenna
J1
COMP1+
COMP1-
Figure 1: Pin Configuration (top view)
Note that the same basic pin configuration applies for all module designs. However, DIO3/SPISEL4 and
DIO2/SPISEL3 are not available on the high power modules.
6 JN-DS-JN5139-xxx-Myy 1v6 © NXP Laboratories UK 2010

JN5139-Z01-M/01R1V

Mfr. #:
Manufacturer:
NXP Semiconductors
Description:
Zigbee Modules (802.15.4) WIRELESS MCU ZIGBEE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union