4.5 Ω R
ON
, 4-/8-Channel
±5 V, +12 V, +5 V, and +3.3 V Multiplexers
Data Sheet
ADG1608/ADG1609
Rev. A Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2015 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
4.5 Ω typical on resistance
1 Ω on-resistance flatness
Up to 470 mA continuous current
±3.3 V to ±8 V dual-supply operation
3.3 V to 16 V single-supply operation
No V
L
supply required
3 V logic-compatible inputs
Rail-to-rail operation
16-lead TSSOP and 16-lead, 3 mm × 3 mm LFCSP
APPLICATIONS
Communication systems
Medical systems
Audio signal routing
Video signal routing
Automatic test equipment
Data acquisition systems
Battery-powered systems
Sample-and-hold systems
Relay replacements
FUNCTIONAL BLOCK DIAGRAMS
ADG1608
1-OF-8
DECODER
A0 A1 A2 EN
S1
S8
D
08318-001
Figure 1.
ADG1609
1-OF-4
DECODER
A0 A1 EN
S1A
DA
DB
S4A
S
1B
S
4B
08318-002
Figure 2.
GENERAL DESCRIPTION
The ADG1608/ADG1609 are monolithic CMOS analog multip-
lexers comprising eight single channels and four differential
channels, respectively. The ADG1608 switches one of eight
inputs to a common output, as determined by the 3-bit binary
address lines, A0, A1, and A2. The ADG1609 switches one of
four differential inputs to a common differential output, as
determined by the 2-bit binary address lines, A0 and A1. An
EN input on both devices is used to enable or disable the device.
When disabled, all channels are switched off.
Each switch conducts equally well in both directions when on
and has an input signal range that extends to the supplies. In the
off condition, signal levels up to the supplies are blocked. All
switches exhibit break-before-make switching action. Inherent
in the design is low charge injection for minimum transients
when switching the digital inputs.
The low on resistance of these switches make them ideal solu-
tions for data acquisition and gain switching applications where
low on resistance and distortion is critical. The on-resistance
profile is very flat over the full analog input range, ensuring
excellent linearity and low distortion when switching audio
signals.
CMOS construction ensures ultralow power dissipation, making
the parts ideally suited for portable and battery-powered
instruments.
PRODUCT HIGHLIGHTS
1. 8 Ω maximum on resistance over temperature.
2. Minimum distortion: THD + N = 0.04%
3. 3 V logic-compatible digital inputs: V
INH
= 2.0 V, V
INL
= 0.8 V.
4. No V
L
logic power supply required.
5. Ultralow power dissipation: <8 nW.
6. 16-lead TSSOP and 16-lead, 3 mm × 3 mm LFCSP.
ADG1608/ADG1609 Data Sheet
Rev. A | Page 2 of 20
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagrams ............................................................. 1
General Description ......................................................................... 1
Product Highlights ........................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
±5 V Dual Supply ......................................................................... 3
12 V Single Supply ........................................................................ 4
5 V Single Supply .......................................................................... 5
3.3 V Single Supply ....................................................................... 6
Continuous Current per Channel, S or D ..................................7
Absolute Maximum Ratings ............................................................8
ESD Caution...................................................................................8
Pin Configurations and Function Descriptions ............................9
Typical Performance Characteristics ........................................... 11
Test Circuits ..................................................................................... 14
Terminology .................................................................................... 17
Outline Dimensions ....................................................................... 18
Ordering Guide .......................................................................... 18
REVISION HISTORY
9/15—Rev. 0 to Rev. A
Change to Table 7 ............................................................................. 8
Updated Outline Dimensions ....................................................... 18
7/09—Revision 0: Initial Version
Data Sheet ADG1608/ADG1609
Rev. A | Page 3 of 20
SPECIFICATIONS
±5 V DUAL SUPPLY
V
DD
= +5 V ± 10%, V
SS
= −5 V ± 10%, GND = 0 V, unless otherwise noted.
Table 1.
Parameter 25°C
−40°C to
+85°C
−40°C to
+125°C
Unit Test Conditions/Comments
ANALOG SWITCH
Analog Signal Range V
DD
to V
SS
V
On Resistance (R
ON
) 4.5 typ V
S
= ±4.5 V, I
S
= −10 mA; see Figure 25
5 7 8 max V
DD
= ±4.5 V, V
SS
= ±4.5 V
On-Resistance Match Between Channels (R
ON
) 0.12 typ V
S
= ±4.5 V, I
S
= −10 mA
0.25 0.3 0.35 max
On-Resistance Flatness (R
FLAT(ON)
) 1 typ V
S
= ±4.5 V, I
S
= −10 mA
1.3 1.7 2 max
LEAKAGE CURRENTS V
DD
= +5.5 V, V
SS
= −5.5 V
Source Off Leakage, I
S
(Off) ±0.02 nA typ
V
S
= ±4.5 V, V
D
= 4.5 V; see Figure 26
±0.1 ±0.5 ±3 nA max
Drain Off Leakage, I
D
(Off) ±0.03 nA typ
V
S
= ±4.5 V, V
D
= 4.5 V; see Figure 26
ADG1608 ±0.15 ±2 ±14 nA max
ADG1609 ±0.15 ±1 ±7 nA max
Channel On Leakage, I
D
, I
S
(On) ±0.03 nA typ V
S
= V
D
= ±4.5 V; see Figure 27
±0.15 ±2 ±14 nA max
DIGITAL INPUTS
Input High Voltage, V
INH
2.0 V min
Input Low Voltage, V
INL
0.8 V max
Input Current, I
INL
or I
INH
±1 nA typ V
IN
= V
GND
or V
DD
±0.1 µA max
Digital Input Capacitance, C
IN
4 pF typ
DYNAMIC CHARACTERISTICS
1
Transition Time, t
TRANSITION
150 ns typ R
L
= 300 Ω, C
L
= 35 pF
182 230 258 ns max V
S
= 2.5 V; see Figure 28
t
ON
(EN) 106 ns typ R
L
= 300 Ω, C
L
= 35 pF
132 150 160 ns max V
S
= 2.5 V; see Figure 30
t
OFF
(EN) 113 ns typ R
L
= 300 Ω, C
L
= 35 pF
144 178 202 ns max V
S
= 2.5 V; see Figure 30
Break-Before-Make Time Delay, t
D
47 ns typ R
L
= 300 Ω, C
L
= 35 pF
30 ns min V
S1
= V
S2
= 2.5 V; see Figure 29
Charge Injection 24 pC typ V
S
= 0 V, R
S
= 0 Ω, C
L
= 1 nF; see Figure 31
Off Isolation −64 dB typ R
L
= 50 Ω, C
L
= 5 pF, f = 1 MHz; see Figure 32
Channel-to-Channel Crosstalk −64 dB typ R
L
= 50 , C
L
= 5 pF, f = 1 MHz; see Figure 34
Total Harmonic Distortion + Noise (THD + N) 0.04 % typ R
L
= 110 Ω, V
S
= 5 V p-p, f = 20 Hz to 20 kHz; see Figure 35
−3 dB Bandwidth R
L
= 50 Ω, C
L
= 5 pF; see Figure 33
ADG1608 40 MHz typ
ADG1609 71 MHz typ
C
S
(Off) 20 pF typ V
S
= 0 V, f = 1 MHz
C
D
(Off)
ADG1608 120 pF typ V
S
= 0 V, f = 1 MHz
ADG1609 61 pF typ V
S
= 0 V, f = 1 MHz
C
D
, C
S
(On)
ADG1608 153 pF typ V
S
= 0 V, f = 1 MHz
ADG1609 85 pF typ V
S
= 0 V, f = 1 MHz
POWER REQUIREMENTS V
DD
= +5.5 V, V
SS
= −5.5 V
I
DD
0.001 µA typ Digital inputs = 0 V or V
DD
1.0 µA max
V
DD
/V
SS
±3.3/±8 V min/max
1
Guaranteed by design, but not subject to production test.

ADG1609BRUZ

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Multiplexer Switch ICs 4:1 71MHz 4.5 Ohm CMOS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union