SL2S5002_SL2S5102 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2012. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.4 — 27 August 2012
193134 19 of 35
NXP Semiconductors
SL2S5002; SL2S5102
ICODE SLIX-L
The requested page(s) is (are) transmitted in the following format and repeated as
necessary (depending on number of pages):
If the Option flag in the request is set to logic 1, the response contains:
The ICODE SLIX-L IC reads the requested page(s) including page protection status and
sends back their value in the response. Additionally the bytes of the UID, which are not
parts of the mask and the slot number in case of 16 slots, are returned. Instead of padding
with zeros up to the next byte boundary, the corresponding bits of the UID are returned.
The mechanism and timing of the INVENTORY PAGE READ command perform the same
as the INVENTORY command which is described in clause 8 of ISO/IEC 15693-3.
The requested page(s) is (are) transmitted in the following format and repeated as
necessary (depending on number of pages):
Remark: The number of bits of the re-transmitted UID can be calculated as follows:
16 slots: 60 bits (bit 64 to bit 5) - mask length rounded up to the next byte boundary
1 slot: 64 bits - mask length rounded up to the next byte boundary
Remark: If the sum of first page number and number of pages exceeds the total available
number of user pages, the number of transmitted pages is less than the requested
number of pages, which means that the last returned page is the highest available user
page, followed by the 16-bit CRC and the EOF.
Example: mask length = 30 bits
Returned: bit 64 to bit 5 (30 bits) = 30 bits gives 4 bytes
Table 30. Page protection status byte
Page Protection Status byte Page data
00h: page is public (not protected with Read password) or the
valid Read password has been transmitted before
16 byte page data content
0Fh: page is protected with the Read password and the valid
Read password has not been transmitted before
no data
Table 31. Response format: Option flag logic 1
SOF Flags Rest of UID which is not part of
the mask and slot number
Data CRC16 EOF
- 8 bits 0 to 64 bit Page status & data 16 bits -
Multiple of 8 bits Repeated as needed
Table 32. Page protection status byte
Page Protection Status Byte Page data
00h: page is public (not protected with Read password) or the
valid Read password has been transmitted before
16 byte page data content
0Fh: page is protected with the Read password and the valid
Read password has not been transmitted before
no data
SL2S5002_SL2S5102 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2012. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.4 — 27 August 2012
193134 20 of 35
NXP Semiconductors
SL2S5002; SL2S5102
ICODE SLIX-L
9.4.3.8 FAST INVENTORY PAGE READ
Command code = B1h
When receiving the FAST INVENTORY PAGE READ command the ICODE SLIX-L IC
behaves the same as the INVENTORY PAGE READ command with the following
exceptions:
The data rate in the direction ICODE SLIX-L IC to the interrogator is twice that defined in
ISO/IEC 15693-3, depending on the Datarate_flag 53 kbit (high data rate) or 13 kbit (low
data rate).
The data rate from the interrogator to the ICODE SLIX-L IC and the time between the
rising edge of the EOF from the interrogator to the ICODE SLIX-L IC remain unchanged
(stay the same as defined in ISO/IEC 15693-3).
In the ICODE SLIX-L IC to the interrogator direction, only the single subcarrier mode is
supported.
9.4.3.9 SET EAS
Command code = A2h
The SET EAS command enables the EAS mode if the EAS mode is not locked. If the EAS
mode is password protected the EAS password has to be first transmitted with the SET
PASSWORD command.
The timing of the command is write alike.
Option 0 (Option flag not set) is supported.
Option 1 (Option flag set) is supported.
Table 33. Example: mask length = 30
Byte 0 Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 UID
mask value including padding with
zeros
- transmitted by
interrogator
returned value transmitted by
ICODE SLIX-L IC
Table 34. Request format
SOF Flags SET EAS IC Mfg code UID CRC16 EOF
- 8 bits 8 bits 8 bits 64 bits
optional
16 bits -
Table 35. Response format when Error_flag set
SOF Flags Error code CRC16 EOF
- 8 bits 8 bits 16 bits -
Table 36. Response format when Error_flag NOT set
SOF Flags CRC16 EOF
- 8 bits 16 bits -
SL2S5002_SL2S5102 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2012. All rights reserved.
Product data sheet
COMPANY PUBLIC
Rev. 3.4 — 27 August 2012
193134 21 of 35
NXP Semiconductors
SL2S5002; SL2S5102
ICODE SLIX-L
9.4.3.10 RESET EAS
Command code = A3h
The RESET EAS command disables the EAS mode if the EAS mode is not locked. If the
EAS mode is password protected the EAS password has to be first transmitted with the
SET PASSWORD command.
The timing of the command is write alike.
Option 0 (Option flag not set) is supported.
Option 1 (Option flag set) is supported.
9.4.3.11 LOCK EAS
Command code = A4h
The LOCK EAS command locks the current state of the EAS mode and the EAS ID. If the
EAS mode is password protected the EAS password has to be first transmitted with the
SET PASSWORD command.
The timing of the command is write alike.
Option 0 (Option flag not set) is supported.
Option 1 (Option flag set) is supported.
Table 37. Request format
SOF Flags RESET EAS IC Mfg code UID CRC16 EOF
- 8 bits 8 bits 8 bits 64 bits optional 16 bits -
Table 38. Response format when Error_flag set
SOF Flags Error code CRC16 EOF
- 8 bits 8 bits 16 bits -
Table 39. Response format when Error_flag NOT set
SOF Flags CRC16 EOF
- 8 bits 16 bits -
Table 40. Request format
SOF Flags LOCK EAS IC Mfg code UID CRC16 EOF
- 8 bits 8 bits 8 bits 64 bits
optional
16 bits -
Table 41. Response format when Error_flag set
SOF Flags Error code CRC16 EOF
- 8 bits 8 bits 16 bits -
Table 42. Response format when Error_flag NOT set
SOF Flags CRC16 EOF
- 8 bits 16 bits -

SL2S5102FUD,003

Mfr. #:
Manufacturer:
NXP Semiconductors
Description:
RFID Transponders ICODE SLIX-L
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet