HSMS-285x Series
Surface Mount Zero Bias Schottky Detector Diodes
Data Sheet
SOT-23/SOT-143 Package Lead Code Identication (top view)
Description
Avagos HSMS-285x family of zero bias Schottky detector
diodes has been designed and optimized for use in small
signal (Pin <-20 dBm) applications at frequencies below
1.5 GHz. They are ideal for RF/ID and RF Tag applications
where primary (DC bias) power is not available.
Important Note: For detector applications with input
power levels greater than –20 dBm, use the HSMS-282x
series at frequencies below 4.0 GHz, and the HSMS-286x
series at frequencies above 4.0 GHz. The HSMS-285x
series IS NOT RECOMMENDED for these higher power
level applications.
Available in various package congurations, these detec-
tor diodes provide low cost solutions to a wide variety
of design problems. Avagos manufacturing techniques
assure that when two diodes are mounted into a single
package, they are taken from adjacent sites on the wafer,
assuring the highest possible degree of match.
Pin Connections and Package Marking
SOT-323 Package Lead Code Identication (top view)
Features
Surface Mount SOT-23/SOT-143 Packages
Miniature SOT-323 and SOT-363 Packages
High Detection Sensitivity:
up to 50 mV/µW at 915 MHz
Low Flicker Noise:
-162 dBV/Hz at 100 Hz
Low FIT (Failure in Time) Rate*
Tape and Reel Options Available
Matched Diodes for Consistent Performance
Better Thermal Conductivity for Higher Power
Dissipation
Lead-free
* For more information see the Surface Mount Schottky Reliability
Data Sheet.
SOT-363 Package Lead Code Identication (top view)
SERIES
C
SINGLE
B
1 2
3
1 2
3
BRIDGE
QUAD
P
UNCONNECTED
TRIO
L
1 2 3
6 5 4
1 2 3
6 5 4
Attention: Observe precautions for
handling electrostatic sensitive devices.
ESD Machine Model (Class A)
ESD Human Body Model (Class 0)
Refer to Avago Application Note A004R:
Electrostatic Discharge Damage and Control.
Notes:
1. Package marking provides orientation and identication.
2.
See “Electrical Specications” for appropriate package marking.
PLx
1
2
3
6
5
4
UNCONNECTED
PAIR
#5
SERIES
#2
SINGLE
#0
1 2
3
1 2
3 4
1 2
3
2
SOT-23/SOT-143 DC Electrical Specications, T
C
= +25°C, Single Diode
Maximum Maximum
Part Package Forward Reverse Typical
Number Marking Lead Voltage Leakage, Capacitance
HSMS- Code Code Conguration V
F
(mV) I
R
(µA) C
T
(pF)
2850 P0 0 Single 150 250 175 0.30
2852 P2 2 Series Pair
[1,2]
2855 P5 5 Unconnected Pair
[1,2]
Test I
F
= 0.1 mA I
F
= 1.0 mA V
R
=2V V
R
= –0.5 V to –1.0V
Conditions f = 1 MHz
Notes:
1. ∆VF for diodes in pairs is 15.0 mV maximum at 1.0 mA.
2. ∆CT for diodes in pairs is 0.05 pF maximum at –0.5V.
RF Electrical Specications, T
C
= +25°C, Single Diode
Part Number Typical Tangential Sensitivity Typical Voltage Sensitivity Typical Video
HSMS- TSS (dBm) @ f = 915 MHz g (mV/µW) @ f = 915 MHz Resistance RV (KΩ)
2850 57 40 8.0
2852
2855
285B
285C
285L
285P
Test Video Bandwidth = 2 MHz Power in = –40 dBm
Conditions Zero Bias R
L
= 100 KΩ, Zero Bias Zero Bias
SOT-323/SOT-363 DC Electrical Specications, T
C
= +25°C, Single Diode
Maximum Maximum
Part Package Forward Reverse Typical
Number Marking Lead Voltage Leakage, Capacitance
HSMS- Code Code Conguration V
F
(mV) I
R
(µA) C
T
(pF)
285B P0 B Single 150 250 175. 0.30
285C P2 C Series Pair
285L PL L Unconnected Trio
285P PP P Bridge Quad
Test I
F
= 0.1 mA I
F
= 1.0 mA VR=2V V
R
= 0.5 V to –1.0V
Conditions f = 1 MHz
Notes:
1. ∆VF for diodes in pairs is 15.0 mV maximum at 1.0 mA.
2. ∆CT for diodes in pairs is 0.05 pF maximum at –0.5V.
3
Equivalent Linear Circuit Model
HSMS-285x chip
SPICE Parameters
Parameter Units HSMS-285x
B
V
V 3.8
C
J0
pF 0.18
E
G
eV 0.69
I
BV
A 3 E-4
I
S
A 3 E-6
N 1.06
R
S
Ω 25
P
B
(V
J
) V 0.35
P
T
(XTI) 2
M 0.5
Absolute Maximum Ratings, T
C
= +25°C, Single Diode
Symbol Parameter Unit Absolute Maximum
[1]
SOT-23/143 SOT-323/363
P
IV
Peak Inverse Voltage V 2.0 2.0
T
J
Junction Temperature °C 150 150
T
STG
Storage Temperature °C -65 to 150 -65 to 150
T
OP
Operating Temperature °C -65 to 150 -65 to 150
θ
jc
Thermal Resistance
[2]
°C/W 500 150
Notes:
1. Operation in excess of any one of these conditions may result in permanent damage to the
device.
2. T
C
= +25°C, where T
C
is dened to be the temperature at the package pins where contact is
made to the circuit board.
ESD WARNING:
Handling Precautions Should Be Taken
To Avoid Static Discharge.
C
j
R
j
R
S
R
j
=
8.33 X 10
-5
nT
I
b
+ I
s
where
I
b
= externally applied bias current in amps
I
s
= saturation current (see table of SPICE parameters)
T
= temperature, °K
n = ideality factor (see table of SPICE parameters)
Note:
To effectively model the packaged HSMS-285x product,
please refer to Application Note AN1124.
R
S
= series resistance (see Table of SPICE parameters)
C
j
= junction capacitance (see Table of SPICE parameters)

HSMS-285C-BLKG

Mfr. #:
Manufacturer:
Broadcom / Avago
Description:
RF Detector RF/ID below 1.5GHz
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union