OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADCMP607BCPZ-R7

P1-P3P4-P6P7-P9P10-P12P13-P14
ADCMP606/ADCMP607 Data Sheet
Rev. C | Page 4 of 14
Parameter Symbol Test Conditions/Comments Min Typ Max Unit
AC PERFORMANCE
1
Rise Time/Fall time t
R
/t
F
10% to 90%,
V
CCI
= V
CCO
= 2.5 V to 5.5 V
160 ps
Propagation Delay t
PD
V
CCI
= V
CCO
= 2.5 V to 5.5 V,
V
OD
= 50 mV
1.2 ns
V
CCI
= V
CCO
= 2.5 V,
V
OD
= 10 mV
2.1 ns
Propagation Delay Skew—Rising to
Falling Transition
T
PINSKEW
V
OD
= 50 mV 40 ps
Overdrive Dispersion 10 mV < V
OD
< 125 mV 2.3 ns
Common-Mode Dispersion
−0.2 V < V
CM
< V
CC
+ 0.2 V
150
ps
Input Stage Bandwidth 750 MHz
RMS Random Jitter RJ V
OD
= 200 mV, 0.5 V/ns 2 ps
Minimum Pulse Width PW
MIN
V
CCI
= V
CCO
= 5.5 V,
PW
OUT
= 90% of PW
IN
1.1 ns
Output Skew Q to
Q
T
DIFFSKEW
50%
20 ps
POWER SUPPLY
Input Supply Voltage Range V
CCI
2.5 5.5 V
Output Supply Voltage Range
V
CCO
2.5
V
Positive Supply Differential (ADCMP607) V
CCI
− V
CCO
Operating −3.0 +3.0 V
V
CCI
− V
CCO
Nonoperating −6 +6 V
Positive Supply Current (ADCMP606) I
VCCI/VCCO
V
CCI
= V
CCO
= 2.5 V 11 17.5 21 mA
V
CCI
= V
CCO
= 5.5 V 16 20.5 26 mA
Input Section Supply Current (ADCMP607) I
VCCI
V
CCI
= 2.5 V 0.5 1.1 1.5 mA
Output Section Supply Current (ADCMP607) I
VCCO
V
CCO
= 2.5 V 10 15.8 18 mA
I
VCCO
V
CCO
= 5.5 V 16 18 25 mA
Power Dissipation P
D
V
CCI
= V
CCO
= 2.5 V 30 46 55 mW
P
D
V
CCI
= V
CCO
= 5.5 V 90 110 150 mW
Power Supply Rejection Ratio PSRR V
CCI
= 2.5 V to 5 V −50 dB
Shutdown Mode I
CCI
V
CCI
= V
CCO
= 2.5 V to 5 V 200 240 800 µA
Shutdown Mode I
CCO
V
CCI
= V
CCO
= 2.5 V to 5 V −30 30 µA
1
V
IN
= 100 mV square input at 50 MHz, V
CM
= 2.5 V, V
CCI
= V
CCO
= 2.5 V, unless otherwise noted.
Data Sheet ADCMP606/ADCMP607
Rev. C | Page 5 of 14
TIMING INFORMATION
Figure 2 illustrates the ADCMP606/ADCMP607 latch timing relationships. Table 2 provides definitions of the terms shown in Figure 2.
1.1V
50%
V
N
± V
OS
DIFFERENTIAL
INPUT VOLTAGE
LATCH ENABLE
Q OUTPUT
t
H
t
PDL
t
PLOH
t
F
V
IN
V
OD
t
S
t
PL
50%
Q OUTPUT
t
PDH
t
PLOL
t
R
05917-025
Figure 2. System Timing Diagram
Table 2. Timing Descriptions
Symbol Symbol Description Timing Description
t
F
Output fall time Amount of time required to transition from a high to a low output as measured at the 20%
and 80% points.
t
H
Minimum hold time Minimum time after the negative transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs.
t
PDH
Input to output high delay Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output low-to-high transition.
t
PDL
Input to output low delay Propagation delay measured from the time the input signal crosses the reference (± the
input offset voltage) to the 50% point of an output high-to-low transition.
t
PL
Minimum latch enable pulse width
Minimum time that the latch enable signal must be high to acquire an input signal
change.
t
PLOH
Latch enable to output high delay Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition.
t
PLOL
Latch enable to output low delay Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition.
t
R
Output rise time
Amount of time required to transition from a low to a high output as measured at the 20%
and 80% points.
t
S
Minimum setup time Minimum time before the negative transition of the latch enable signal occurs that an
input signal change must be present to be acquired and held at the outputs.
V
OD
Voltage overdrive Difference between the input voltages V
A
and V
B
.
ADCMP606/ADCMP607 Data Sheet
Rev. C | Page 6 of 14
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter Rating
Supply Voltages
Input Supply Voltage (V
CCI
to GND)
−0.5 V to +6.0 V
Output Supply Voltage
(V
CCO
to GND)
−0.5 V to +6.0 V
Positive Supply Differential
(V
CCI
− V
CCO
)
−6.0 V to +6.0 V
Input Voltages
Input Voltage −0.5 V to V
CCI
+ 0.5 V
Differential Input Voltage ±(V
CCI
+ 0.5 V)
Maximum Input/Output Current ±50 mA
Shutdown Control Pin
Applied Voltage (S
DN
to GND) −0.5 V to V
CCO
+ 0.5 V
Maximum Input/Output Current ±50 mA
Latch/Hysteresis Control Pin
Applied Voltage (HYS to GND) −0.5 V to V
CCO
+ 0.5 V
Maximum Input/Output Current ±50 mA
Output Current ±50 mA
Temperature
Operating Temperature, Ambient
−40°C to +125°C
Operating Temperature, Junction 150°C
Storage Temperature Range −65°C to +150°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
THERMAL RESISTANCE
θ
JA
is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 4. Thermal Resistance
Package Type θ
JA
1
Unit
ADCMP606 6-Lead SC70 426 °C/W
ADCMP607 12-Lead LFCSP
62
°C/W
1
Measurement in still air.
ESD CAUTION
P1-P3P4-P6P7-P9P10-P12P13-P14

ADCMP607BCPZ-R7

Mfr. #:
Buy ADCMP607BCPZ-R7
Manufacturer:
Analog Devices Inc.
Description:
Analog Comparators RR Fast 2.5-5.5V SGL-Supply CML
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet