1
LTC1563-2/LTC1563-3
156323fa
Extremely Easy to Use—A Single Resistor Value
Sets the Cutoff Frequency (256Hz < f
C
< 256kHz)
Extremely Flexible—Different Resistor Values
Allow Arbitrary Transfer Functions with or without
Gain (256Hz < f
C
< 256kHz)
Supports Cutoff Frequencies Up to 360kHz Using
FilterCAD
TM
LTC1563-2: Unity-Gain Butterworth Response Uses a
Single Resistor Value, Different Resistor Values
Allow Other Responses with or without Gain
LTC1563-3: Unity-Gain Bessel Response Uses a
Single Resistor Value, Different Resistor Values
Allow Other Responses with or without Gain
Rail-to-Rail Input and Output Voltages
Operates from a Single 3V (2.7V Min) to ±5V Supply
Low Noise: 36µV
RMS
for f
C
= 25.6kHz, 60µV
RMS
for
f
C
= 256kHz
f
C
Accuracy < ±2% (Typ)
DC Offset < 1mV
Cascadable to Form 8th Order Lowpass Filters
Available in Narrow SSOP-16 Package
The LTC
®
1563-2/LTC1563-3 are a family of extremely
easy-to-use, active RC lowpass filters with rail-to-rail
inputs and outputs and low DC offset suitable for systems
with a resolution of up to 16 bits. The LTC1563-2, with a
single resistor value, gives a unity-gain Butterworth
response. The LTC1563-3, with a single resistor value,
gives a unity-gain Bessel response. The proprietary
architecture of these parts allows for a simple resistor
calculation:
R = 10k (256kHz/f
C
); f
C
= Cutoff Frequency
where f
C
is the desired cutoff frequency. For many appli-
cations, this formula is all that is needed to design a filter.
By simply utilizing different valued resistors, gain and
other responses are achieved.
The LTC1563-X features a low power mode, for the lower
frequency applications, where the supply current is re-
duced by an order of magnitude and a near zero power
shutdown mode.
The LTC1563-Xs are available in the narrow SSOP-16
package (Same footprint as an SO-8 package).
Discrete RC Active Filter Replacement
Antialiasing Filters
Smoothing or Reconstruction Filters
Linear Phase Filtering for Data Communication
Phase Locked Loops
Single 3.3V, 256Hz to 256kHz Butterworth Lowpass Filter
Active RC, 4th Order
Lowpass Filter Family
, LTC and LT are registered trademarks of Linear Technology Corporation.
0.1µF
3.3V
V
OUT
V
IN
R
R
R
R
R
R
f
C
= 256kHz
1563 TA01
LTC1563-2
0.1µF
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
LP
SA
NC
INVA
NC
LPA
AGND
V
V
+
LPB
NC
INVB
NC
SB
NC
EN
10k
R
()
FREQUENCY (Hz)
10k1k100
GAIN (dB)
10
0
–10
–20
–30
–40
–50
–60
–70
–80
100k 1M
1563 TA02
R = 10M
f
C
= 256Hz
R = 10k
f
C
= 256kHz
Frequency Response
APPLICATIO S
U
FEATURES
TYPICAL APPLICATIO
U
DESCRIPTIO
U
FilterCAD is trademark of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
2
LTC1563-2/LTC1563-3
156323fa
LTC1563-2CGN
LTC1563-3CGN
LTC1563-2IGN
LTC1563-3IGN
T
JMAX
= 150°C, θ
JA
= 135°C/ W
ORDER PART
NUMBER
Total Supply Voltage (V
+
to V
) ............................... 11V
Maximum Input Voltage at
Any Pin ....................... (V
– 0.3V) V
PIN
(V
+
+ 0.3V)
Power Dissipation.............................................. 500mW
Operating Temperature Range
LTC1563C ............................................... 0°C to 70°C
LTC1563I............................................ 40°C to 85°C
Storage Temperature Range ................. 65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
(Note 1)
ABSOLUTE MAXIMUM RATINGS
W
WW
U
PACKAGE/ORDER INFORMATION
W
U
U
ELECTRICAL CHARACTERISTICS
TOP VIEW
GN PACKAGE
16-LEAD PLASTIC SSOP
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
LP
SA
NC
INVA
NC
LPA
AGND
V
V
+
LPB
NC
INVB
NC
SB
NC
EN
NOTE: PINS LABELED NC ARE NOT CONNECTED
INTERNALLY AND SHOULD BE CONNECTED TO THE
SYSTEM GROUND
The
denotes specifications which apply over the full operating temperature range, otherwise specifications are T
A
= 25°C.
V
S
= Single 4.75V, EN pin to logic “low,” Gain = 1, R
FIL
= R11 = R21 = R31 = R12 = R22 = R32, specifications apply to both the high
speed (HS) and low power (LP) modes unless otherwise noted.
Consult LTC Marketing for Military grade parts.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Specifications for Both LTC1563-2 and LTC1563-3
Total Supply Voltage (V
S
), HS Mode 311V
Total Supply Voltage (V
S
), LP Mode 2.7 11 V
Output Voltage Swing High (LPB Pin) V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 2.9 2.95 V
HS Mode V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.55 4.7 V
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.8 4.9 V
Output Voltage Swing Low (LPB Pin) V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 0.015 0.05 V
HS Mode V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 0.02 0.05 V
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.95 4.9 V
Output Swing High (LPB Pin) V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 2.6 2.65 V
LP Mode V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.55 4.65 V
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.8 4.9 V
Output Swing Low (LPB Pin) V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 0.01 0.05 V
LP Mode V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 0.015 0.05 V
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k, R
L
= 10k to GND 4.95 4.9 V
DC Offset Voltage, HS Mode V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k ±1.5 ±3mV
(Section A Only) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k ±1.0 ±3mV
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k ±1.5 ±3mV
DC Offset Voltage, LP Mode V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±6mV
(Section A Only) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±6mV
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±7mV
DC Offset Voltage, HS Mode V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k ±1.5 ±3mV
(Input to Output, Sections A, B Cascaded) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k ±1.0 ±3mV
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k ±1.5 ±3mV
15632
15633
15632I
15633I
GN PART
MARKING
Order Options Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking: http://www.linear.com/leadfree/
3
LTC1563-2/LTC1563-3
156323fa
ELECTRICAL CHARACTERISTICS
PARAMETER CONDITIONS MIN TYP MAX UNITS
DC Offset Voltage, LP Mode V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±7mV
(Input to Output, Sections A, B Cascaded) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±7mV
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k ±2 ±8mV
DC Offset Voltage Drift, HS Mode V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
(Input to Output, Sections A, B Cascaded) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
DC Offset Voltage Drift, LP Mode V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
(Input to Output, Sections A, B Cascaded) V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k 10 µV/°C
AGND Voltage V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 2.35 2.375 2.40 V
Power Supply Current, HS Mode V
S
= 3V, f
C
= 25.6kHz, R
FIL
= 100k 8.0 14 mA
V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 10.5 17 mA
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k 15 23 mA
Power Supply Current, LP Mode V
S
= 2.7V, f
C
= 25.6kHz, R
FIL
= 100k 1.0 1.8 mA
V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 1.4 2.5 mA
V
S
= ±5V, f
C
= 25.6kHz, R
FIL
= 100k 2.3 3.5 mA
Shutdown Mode Supply Current V
S
= 4.75V, f
C
= 25.6kHz, R
FIL
= 100k 120 µA
EN Input V
S
= 3V 0.8 V
Logic Low Level V
S
= 4.75V 1V
V
S
= ±5V 1V
EN Input V
S
= 3V 2.5 V
Logic High Level V
S
= 4.75V 4.3 V
V
S
= ±5V 4.4 V
LP V
S
= 3V 0.8 V
Logic Low Level V
S
= 4.75V 1V
V
S
= ±5V 1V
LP V
S
= 3V 2.5 V
Logic High Level V
S
= 4.75V 4.3 V
V
S
= ±5V 4.4 V
LTC1563-2 Transfer Function Characteristics
Cutoff Frequency Range, f
C
V
S
= 3V 0.256 256 kHz
HS Mode V
S
= 4.75V 0.256 256 kHz
(Note 2) V
S
= ±5V 0.256 256 kHz
Cutoff Frequency Range, f
C
V
S
= 2.7V 0.256 25.6 kHz
LP Mode V
S
= 4.75V 0.256 25.6 kHz
(Note 2) V
S
= ±5V 0.256 25.6 kHz
Cutoff Frequency Accuracy, HS Mode V
S
= 3V, R
FIL
= 100k 2.0 ±1.5 3.5 %
f
C
= 25.6kHz V
S
= 4.75V, R
FIL
= 100k 2.0 ±1.5 3.5 %
V
S
= ±5V, R
FIL
= 100k 2.0 ±1.5 3.5 %
Cutoff Frequency Accuracy, HS Mode V
S
= 3V, R
FIL
= 10k –5 ±1.5 2.5 %
f
C
= 256kHz V
S
= 4.75V, R
FIL
= 10k –5 ±1.5 2.5 %
V
S
= ±5V, R
FIL
= 10k –5 ±1.5 2.5 %
Cutoff Frequency Accuracy, LP Mode V
S
= 2.7V, R
FIL
= 100k –3 ±1.5 3 %
f
C
= 25.6kHz V
S
= 4.75V, R
FIL
= 100k –3 ±1.5 3 %
V
S
= ±5V, R
FIL
= 100k –3 ±1.5 3 %
Cutoff Frequency Temperature Coefficient (Note 3) ±1 ppm/°C
The denotes specifications which apply over the full operating temperature range, otherwise specifications are T
A
= 25°C.
V
S
= Single 4.75V, EN pin to logic “low,” Gain = 1, R
FIL
= R11 = R21 = R31 = R12 = R22 = R32, specifications apply to both the high
speed (HS) and low power (LP) modes unless otherwise noted.

LTC1563-3IGN#PBF

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Active Filter Active RC, 4th Order Lpass Filt Fam
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union