SE2611T-R

DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014 7
Notes:
1. All dimensions are in millimeters.
2. Dimensions and tolerances according to ASME Y14.5M-1994.
3. Unless specified, dimensions are symmetrical about center lines.
4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum),
via hole to be filled with conductive paste and plated over.
5. Stencil recommendations: 0.10 mm stencil thickness, laser cut
apertures, trapezoidal walls and rounded corners offer better paste release.
6. Solder mask recommendations: contact board fabricator for recommended
solder mask offset and tolerance.
9X ø0.254
3X 0.62
Via Pattern
(Note 4)
Board Metal
Solder Mask Pattern
(Note 6)
Stencil Pattern
(Note 5)
3.40
1.80
0.400
Typ
56% solder coverage
on center pads
0.20
Typ
1.80
3.40
3X 0.62
0
3X 0.62
3X 0.62
0
0
0
0.55 Typ
3.40
3.50
0.65 Typ
3.40
0.55 Typ
0.60 Typ
0.60 Typ
0.20
0.20
0.400
Typ
0.20
Typ
Package
Outline
0.30
Typ
0.400
Typ
1.60
1.60
3.50
Y0975
Figure 4. PCB Layout Footprint for the SE2611T
Y0960
Pin 1
Indicator
Part Number
Lot Code
SiGe
2611T
XXXXX
Figure 5. Typical Case Markings
(Top View)
DATA SHEET • SE2611T 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
8 May 30, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202404B
Top View Bottom View
Pin 1
Indicator
Pin 1 Indicator
Detail A
Exposed Pad
Detail A
Scale: 2X
20 Places
Side View
3.00 ± 0.05
0.05 C
Notes:
1. All measurements are in millimeters.
2. Dimensions and tolerances according to ASME Y14.5M-1994.
3. Unless otherwise specified, the following values apply:
Decimal Tolerance: Angular Tolerance:
X.X (1 place)
± 0.1 mm ±1/2°
X.XX (2 places) ± 0.05 mm
X.XXX (3 places) ± 0.025 mm
4. Coplanarity applies to the terminals as well as all other bottom surface metallization.
5. Dimension applies to metallized terminal. If terminal tip has a radius, dimension
should not be measured in that radius area.
6. Unless specified, dimensions are symmetrical about center lines.
0.05 C
0.55 ± 0.05
Seating
Plane
A
B
Y0977
0.35 ± 0.05
2X
2X
0.20 ± 0.05
5
1.70 ± 0.05
0.40
0.02 +0.03
–0.02
0.30 X 45°
20X 0.25 Min
0.05
M
C
0.10
M
C A B
0.05 C
3.00 ± 0.05
0.05 C
21X
4
1.70 ± 0.05
2X R0.075
0.152 Ref
R0.075
Typ
C
Figure 6. SE2611T 20-Pin QFN Package Dimensions
1.75 ± 0.1
ø1.55
±
0.05
4.0 ± 0.1
5.50- ± 0.1
(Note 3)
Pin 1
Indicator
Notes:
1. Measured from center line of sprocket hole to center line of pocket.
2. 10-sprocket hole pitch cumulative tolerance: ±0.20.
3. Measured from center line of sprocket hole to center line of pocket.
4. Other material available.
5. Typical SR of form tape from 10
5
to 10
11
Ω/sq.
6. All dimensions are in millimeters.
3.30 ± 0.1
ø1.5 Min
12.00 ± 0.3
Y
Section Y
0.30 ± 0.05
Ref 3°
3.30 ± 0.1
0.80 ± 0.1
8.00 ± 0.1
2.0 ± 0.1
(Note 1)
Y
A
Ref
R0.6
Ref
R0.50
Ref
R0.35
View A
Y0978
Figure 7. SE2611T 20-Pin QFN Carrier Tape Dimensions
DATA SHEET • SE2611T: 2.4 GHZ HIGH EFFICIENCY WIRELESS LAN/BT FRONT END
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
202404B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • May 30, 2014 9
Ordering Information
Model Name Manufacturing Part Number Evaluation Board Part Number
SE2611T: 2.4 GHz High Efficiency Wireless LAN/BT Front End SE2611T SE2611T-EK1
Copyright © 2012-2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for
identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by
reference.

SE2611T-R

Mfr. #:
Manufacturer:
Skyworks Solutions, Inc.
Description:
RF Front End 2.4GHz 802.11bgn 3.3Volt -40C +85C
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet