73S8009R-IMR/F Datasheet 73S8009R-IM/F, 73S8009R-IL/F, 73S8009R-IMR/F | P7-P9

DS_8009R_056 73S8009R Data Sheet

Rev. 1.3 7

Name

(SO28)

(QFN20)

Type Description

I/OUC 5 1 I/O System controller data I/O to/from the card. Includes a pull-

up resistor to V

DD.

AUX1UC 6 NA I/O System controller auxiliary data I/O to/from the card.

Includes a pull-up resistor to V

DD.

AUX2UC 7 NA I/O System controller auxiliary data I/O to/from the card.

Includes a pull-up resistor to V

DD.

CMDVCC%

CMDVCC#

Logic low on one or both of these pins will cause the LDO to

ramp the Vcc supply to the smart card and smart card

interface to the value described in the following table:

CMDVCC%

CMDVCC#

Output Voltage

0 0 1.8 V

0 1 5.0 V

1 0 3.0 V

1 1 LDO off

Refer to for additional information on the CMDVCC% and

CMDVCC# operation.

RSTIN 10 4 I Reset Input. This signal is the reset command to the card.

RDY 12 6 O Signal to controller indicating the 73S8009R is ready

because V

is above the required value after CMDVCC%

and/or CMDVCC# is asserted low. A 20 KΩ pull-up resistor

to V

is provided internally. The pull-up is disabled in

PWRDN and CS=0 modes.

PWRDN 13 7 I

PWRDN=1 puts the circuit into low-power mode with all

analog functions disabled. The circuit will recover from the

PWRDN state in the same manner as recovery from a POR

event, taking approximately 1 ms. PWRDN assertion when

either CMDVCC% or CMDVCC# is low has no effect and is

ignored. There is no pull-up or pull-down provided on this pin.

73S8009R Data Sheet DS_8009R_056

8 Rev. 1.3

2 Electrical Specifications

This section provides the following:

 Absolute Maximum Ratings

 Recommended Operating Conditions

 Smart Card Interface Requirements

 Digital Signals Characteristics

 DC Characteristics

 Voltage / Temperature Fault Detection Circuits

2.1 Absolute Maximum Ratings

Table 2 lists the maximum operating conditions for the 73S8009R. Permanent device damage may occur

if absolute maximum ratings are exceeded. Exposure to the extremes of the absolute maximum rating for

extended periods may affect device reliability.

Table 2: Absolute Maximum Device Ratings

Parameter Rating

Supply voltage V

-0.5 to 4.0 VDC

Supply voltage V

-0.5 to 6.5 VDC

Input voltage for digital inputs -0.3 to (V

+0.5) VDC

Storage temperature -60 °C to +150 °C

Pin voltage (except card interface) -0.3 to (V

+ 0.5) VDC

Pin voltage (card interface) -0.3 to (V

+ 0.5) VDC

ESD tolerance – Card interface pins +/- 6 kV

ESD tolerance – Other pins +/- 2 kV

Note: ESD testing on smart card pins is HBM condition, 3 pulses, each polarity referenced to ground.

Smart card pins are protected against shorts between any combination of smart card pins.

2.2 Recommended Operating Conditions

Function operation should be restricted to the recommended operating conditions specified in Table 3.

Table 3: Recommended Operating Conditions

Parameter Rating

Supply voltage V

2.7 to 3.6 VDC

Supply voltage V

for Class A-B-C Reader 4.75 to 6.0 VDC

Ambient operating temperature -40 °C to +85 °C

DS_8009R_056 73S8009R Data Sheet

Rev. 1.3 9

2.3 Smart Card Interface Requirements

Table 4 lists the 73S8009R Smart Card interface requirements.

Table 4: DC Smart Card Interface Requirements

Symbol Parameter Condition Min Nom Max Unit

Card Power Supply (V

) Regulator

General Conditions: -40 °C < T < 85 °C, 4.75 V < V

< 6.0 V, 2.7 V < V

< 6.0 V

Card supply voltage

including ripple and

noise

Inactive mode -0.1 – 0.1 V

Inactive mode I

= 1 mA -0.1 – 0.4

Active mode; I

< 65 mA; 5 V 4.65 – 5.25

Active mode; I

< 65mA; 5 V,

NDS condition

4.75 – 5.25

Active mode; I

< 65 mA; 3 V 2.85 – 3.15

Active mode; I

< 40 mA; 1.8 V 1.68 – 1.92

Active mode; single pulse of

100 mA for 2 µs; 5 V, fixed load

= 25 mA

4.6 – 5.25

Active mode; single pulse of

100 mA for 2 µs; 3 V, fixed load

= 25 mA

2.7 – 3.15

Active mode; current pulses of

40 nAs with peak |I

< 200 mA, t < 400 ns; 5 V

4.6 – 5.25

Active mode; current pulses of

40 nAs with peak |I

< 200 mA, t <400 ns; 3 V

2.7 – 3.15

Active mode; current pulses of

20 nAs with peak |I

< 100 mA, t <400 ns; 1.8 V

1.62 – 1.92

CCrip

Ripple f

RIPPLE

= 20 kHz – 200 MHz – – 350 mV

CCmax

Card supply output

current

Static load current, V

> 1.65 V –

–

40 mA

Static load current, VCC > 4.6 V

or 2.7 V as selected

– – 90

CCF

fault current Class A, B (5 V and 3 V) 100 – 180 mA

Class C (1.8 V) 60 – 130

Vcc slew rate, rise rate

on activate

= 1.0 µF

0.06 0.15 0.25 V/μs

Vcc slew rate, fall rate on

de-activate

= 1.0 µF on V

0.075 0.15 0.6 V/μs

RDY

ready voltage, V

rising (RDY = 1)

5 V operation 4.6 – – V

3 V operation 2.75 – –

1.8 V operation 1.65 – –

External filter capacitor

to GND)

should be ceramic with

low ESR (< 100 mΩ)

ISO 7816-13 application

1.0

µF

EMV 4.1 application

3.3

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15 P16-P18 P19-P21 P22-P23

73S8009R-IMR/F

Mfr. #:

Buy 73S8009R-IMR/F

Manufacturer:

Maxim Integrated

Description:

I/O Controller Interface IC Smart Card Interface IC

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

73S8009R-IMR/F

73S8009R-IMR/F

Products related to this Datasheet