OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

2884907

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P28
IB IL SGI 2/P-PAC
7647_en_04 PHOENIX CONTACT 4
Dimensions (nominal sizes in mm)
Width 48.8 mm
Height 136 mm
Depth 71.5 mm
4 Technical data
135
119,8
71,5
General data
Color green
Weight 220 g
Operating mode Process data operation with 3 words, PCP with 1 word
Ambient temperature (operation) -25 °C ... 55 °C
Ambient temperature (storage/transport) -25 °C ... 85 °C
Permissible humidity (operation) 10 % ... 95 % (according to DIN EN 61131-2)
Permissible humidity (storage/transport) 10 % ... 95 % (according to DIN EN 61131-2)
Air pressure (operation) 70 kPa ... 106 kPa (up to 3000 m above sea level)
Air pressure (storage/transport) 70 kPa ... 106 kPa (up to 3000 m above sea level)
Degree of protection IP20
Protection class III, IEC 61140, EN 61140, VDE 0140-1
Connection data Inline connectors
Connection method Spring-cage connection
Conductor cross section, solid 0.08 mm² ... 1.5 mm²
Conductor cross section, stranded 0.08 mm² ... 1.5 mm²
Conductor cross section [AWG] 28 ... 16
Interface Inline local bus
Connection method Inline data jumper
Transmission speed 500 kBit/s
Transmission physics Copper
Inline potential routing / Power consumption
Communications power U
L
7.5 V DC
Current consumption from U
L
max. 100 mA, typ. 85 mA
IB IL SGI 2/P-PAC
7647_en_04 PHOENIX CONTACT 5
I/O supply voltage U
ANA
24 V DC
Current consumption from U
ANA
max. 100 mA
25 mA (in case of typical load of 350 Ohm per channel)
7 mA (for no-load operation without strain gauge or display)
80 mA (For a maximum load of 55 Ω and display)
Power consumption Typ. 1.2 W (Device in nominal operation)
max. 3.2 W (Device with maximum load)
Inline potential routing / Power consumption
Voltage output
Number of outputs 2
Impedance > 55 Ω (per channel)
Output voltage typ. 5 V
Output current max. 90 mA (per channel)
Short-circuit protection of the voltage outputs Yes, at least 1 minute through temperature monitoring
Floating N/O contact
Quantity 2 (K
a1
-K
b1
, K
a2
-K
b2
)
Volume resistance < 1 Ω (typical)
Volume resistance 5 Ω (maximum)
Typical response time 100 ms (typical)
Serial interface
Name V.24 (RS-485) serial interface
Network Yes
Addressing Address 1 = Measured gross/net value
Address 2 = Measured tare value
Termination resistor 120 Ω
Transmission protocol STX/ETX
Input channels for strain gauge
Number of inputs 2
Connection method 6 or 4-wire, twisted pair shielded cable
Characteristics ±1mV/V, ±2mV/V, ±3mV/V, ±3.33mV/V, ±4mV/V, ±5mV/V
Bridge difference U
d
Measuring range specified by selecting the characteristic
Bridge voltage U
0
5 V
Measured value representation 15 bits + sign bit (process data); 15 bits + sign bit and measured display value in
the ASCII character set (PCP)
Process data update typ. 100 ms (12.5 ms, depends on the configuration)
Resolution A/D 24 bit
A/D conversion time Typ. 100 ms (12.5 ms, depends on the configuration)
Averaging Can be parameterized: None or using 4,16 or 32 measured values; default set-
ting: using 16 measured values
Limit frequency 0.3 Hz (with default setting)
Programming Data
ID code (hex) DF
ID code (dec.) 223
Length code (hex) 03
Length code (dec.) 03
Process data channel 48 Bit
Input address area 6 Byte
IB IL SGI 2/P-PAC
7647_en_04 PHOENIX CONTACT 6
Output address area 6 Byte
Parameter channel (PCP) 2 Byte
Register length (bus) 64 Bit
Programming Data
PROFIBUS telegram data
Required parameter data 23 Byte
Need for configuration data 5 Byte
Error messages to the higher level control or computer system
Failure of the power supply at U
ANA
Error message in the process data
Failure of or insufficient communications power U
L
I/O error message sent to the bus coupler
Peripheral fault Error message in the process data
Electrical isolation/isolation of the voltage areas
Logic/analog I/O (digital isolator) 500 V AC, 50 Hz, 1 min
RS-485/analog I/O (isolating distance) 500 V AC, 50 Hz, 1 min
N/O contact K
a1
- K
b1
/ analog I/O (isolating distance) 500 V AC, 50 Hz, 1 min
N/O contact K
a2
- K
b2
/ analog I/O (isolating distance) 500 V AC, 50 Hz, 1 min
Functional earth ground/analog I/O (isolating distance) 500 V AC, 50 Hz, 1 min
Logic/RS-485 (digital isolator) 500 V AC, 50 Hz, 1 min
N/O contact K
a1
- K
b1
/ RS-485 (isolating distance) 500 V AC, 50 Hz, 1 min
N/O contact K
a2
- K
b2
/ RS-485 (isolating distance) 500 V AC, 50 Hz, 1 min
Functional earth ground/RS-485 (isolating distance) 500 V AC, 50 Hz, 1 min
Logic / N/O contact K
a1
- K
b1
(optocoupler) 500 V AC, 50 Hz, 1 min
N/O contact K
a2
- K
b2
/N/O contact K
a1
- K
b1
(isolating distance) 500 V AC, 50 Hz, 1 min
Functional earth ground / N/O contact K
a1
- K
b1
(isolating distance) 500 V AC, 50 Hz, 1 min
Logic / N/O contact K
a2
- K
b2
(optocoupler) 500 V AC, 50 Hz, 1 min
Functional earth ground / N/O contact K
a2
- K
b2
(isolating distance) 500 V AC, 50 Hz, 1 min
Logic/functional earth ground (isolating distance) 500 V AC, 50 Hz, 1 min
Approvals
For the latest approvals, please visit www.phoenixcontact.net/products.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P27P28-P28

2884907

Mfr. #:
Buy 2884907
Manufacturer:
Phoenix Contact
Description:
Controllers IB IL SGI 2/P-PAC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet