FOD2200 — Low Input Current Logic Gate Optocouplers
©2004 Fairchild Semiconductor Corporation www.fairchildsemi.com
FOD2200 Rev. 1.0.4
August 2010
FOD2200
Low Input Current Logic Gate Optocouplers
Features
1kV/µs minimum common mode rejection
Compatible with LSTTL, TTL, and CMOS logic
Wide V
CC
range (4.5V to 20V)
2.5Mbd guaranteed over temperature
Low input current (1.6mA)
Three state output (no pullup resistor required)
Guaranteed performance from 0°C to 85°C
Hysteresis
Safety and regulatory approved
– UL1577, 5000 V
RMS
for 1 min.
– IEC60747-5-2
>8.0mm clearance and creepage distance
(option ‘T’ or ‘TS’)
1,414V Peak Working Insulation Voltage (V
IORM
)
Applications
Isolation of high speed logic systems
Computer peripheral interfaces
Microprocessor system interfaces
Ground loop elimination
Pulse transformer replacement
Isolated bus driver
High speed line receiver
Description
The FOD2200 is an optically coupled logic gate that
combine an AlGaAs LED and an integrated high gain
photo detector. The detector has a three state output
stage and has a detector threshold with hysteresis. The
three state output eliminates the need for a pullup resis-
tor and allows for direct drive of data busses. The hyster-
esis provides differential mode noise immunity and
eliminates the potential for output signal chatter.
The Electrical and Switching Characteristics of the
FOD2200 are guaranteed over the temperature range of
0°C to 85°C and a V
CC
range of 4.5V to 20V. Low I
F
and
wide V
CC
range allow compatibility with TTL, LSTTL, and
CMOS logic and result in lower power consumption
compared to other high speed opto-couplers. Logic
signals are transmitted with a maximum propagation
delay of 300ns. The FOD2200 is useful for isolating high
speed logic interfaces, buffering of input and output
lines, and implementing isolated line receivers in high
noise environments.
Truth Table
(Positive Logic)
Functional Block Diagram and Schematic Package Outlines
LED Enable Output
On H Z
Off H Z
On L H
Off L L
7
1
2
3
4
5
6
8
NC
ANODE
CATHODE
NC
GND
V
CC
V
O
SHIELD
V
E
I
F
SHIELD
V
F
V
CC
V
O
GND
I
CC
I
O
+
2
3
8
5
V
E
7
6
I
E
8
8
1
8
1
1
8
1
©2004 Fairchild Semiconductor Corporation www.fairchildsemi.com
FOD2200 Rev. 1.0.4 2
FOD2200 — Low Input Current Logic Gate Optocouplers
Safety and Insulation Ratings
As per IEC 60747-5-2. This optocoupler is suitable for “safe electrical insulation” only within the safety limit data.
Compliance with the safety ratings shall be ensured by means of protective circuits.
Symbol Parameter Min. Typ. Max. Unit
Installation Classifications per DIN VDE 0110/1.89 Table 1
For Rated Mains Voltage < 150Vrms I–IV
For Rated Mains Voltage < 300Vrms I–IV
For Rated Mains Voltage < 450Vrms I–III
For Rated Mains Voltage < 600Vrms I–III
For Rated Mains Voltage < 1000Vrms (Option T, TS) I–III
Climatic Classification 40/85/21
Pollution Degree (DIN VDE 0110/1.89) 2
CTI Comparative Tracking Index 175
V
PR
Input to Output Test Voltage, Method b,
V
IORM
x 1.875 = V
PR
, 100% Production Test with
tm = 1 sec., Partial Discharge < 5pC
2651
Input to Output Test Voltage, Method a,
V
IORM
x 1.5 = V
PR
, Type and Sample Test with
tm = 60 sec.,Partial Discharge < 5 pC
2121
V
IORM
Max Working Insulation Voltage 1,414 V
peak
V
IOTM
Highest Allowable Over Voltage 6000 V
peak
External Creepage 8 mm
External Clearance 7.4 mm
External Clearance (for Option T or TS - 0.4” Lead Spacing) 10.16 mm
Insulation Thickness 0.5 mm
Safety Limit Values – Maximum Values Allowed in the
Event of a Failure
T
Case
Case Temperature 150 °C
I
S,INPUT
Input Current 10 mA
P
S,OUTPUT
Output Power (Duty Factor
2.7%) 150 mW
R
IO
Insulation Resistance at T
S
, V
IO
= 500V 10
9
©2004 Fairchild Semiconductor Corporation www.fairchildsemi.com
FOD2200 Rev. 1.0.4 3
FOD2200 — Low Input Current Logic Gate Optocouplers
Absolute Maximum Ratings
(T
A
= 25°C unless otherwise specified)
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended
operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not
recommend exceeding them or designing to absolute maximum ratings.
*The initial switching threshold is 1.6mA or less. It is recommended that 2.2mA be used to permit at least a 20%
CTR degradation guardband.
Symbol Parameter Value Units
T
STG
Storage Temperature -40 to +125 °C
T
OPR
Operating Temperature -40 to +85 °C
T
SOL
Lead Solder Temperature (1.6mm below seating plane) 260 for 10 sec °C
EMITTER
I
F (PK)
Peak Transient Input Current (
1µs PW, 300pps) 1.0 A
I
F
Average Forward Input Current 10 mA
V
R
Reverse Input Voltage 5.0 V
P
D
Output Power Dissipation (No derating required up to 85°C) 45 mW
DETECTOR
V
CC
Supply Voltage 0 to 20 V
I
O
Average Output Current 25 mA
V
E
Three State Enable Voltage -0.5 to 20 V
V
O
Output Voltage -0.5 to 20 V
P
D
Output Power Dissipation (No derating required up to 85°C) 150 mW
Symbol Parameter Min. Max. Units
I
F(ON)
Forward Input Current 1.6* 5 mA
I
F(OFF)
Forward Input Current 0.1 mA
V
CC
Supply Voltage, Output 4.5 20 V
V
EL
Enable Voltage, LOW Level 0 0.8 V
V
EH
Enable Voltage, HIGH Level 2.0 20 V
T
A
Operating Temperature 0 +85 °C
NFan Out (TTL Load) 4

FOD2200T

Mfr. #:
Manufacturer:
ON Semiconductor / Fairchild
Description:
High Speed Optocouplers Low Input Current Logic Gate Coupler
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union