Sheet 13/20
製品規格/Product Specification
テ-ピング仕/Taping Specification
品種名/Type NumberLNJ123W8PRZ
松下統一品番/Matsushita Unified Parts Number
LNJ123W8PRZ
2. リール仕/Reel Specification
2004-11-02 2008-04-21
Established Revised
Panasonic Semiconductor Opto Devices Co., Ltd.
φ180.0
+0
-
3.0
φ13.0±0.2
2.0±0.2
9.0
±
0.3
11.4
±
1.0
φ60.0
+1.0
-
0
A-A’SECT
注意/Notes
1)本製品は、JEITA ETX-7001 適用品である。
This part is the application of JEITA ETX-7001.
2)単位/Unitmm
Sheet 14/20
製品規格/Product Specification
テ-ピング仕/Taping Specification
品種名/Type NumberLNJ123W8PRZ
松下統一品番/Matsushita Unified Parts Number
LNJ123W8PRZ
3. エンボステーピング仕/Embossed taping specifications
1) 送り穴は引出し方向に向かって左側にること。
Pin-feed holes should be on the left side on the tape in the pulling direction.
2)
テーピング内 LED 極性は上記実装部の通りとする
Refer to mounting part for LED’s polarity in taping .
3)
リ-ダ-部分はカバーテ-プのみとし 200 mm 以上とする
The leader part is saved as cover tape, which should be 200 mm or longer.
4)
テ-ング前後部にそれぞれ 10 以上のエンス空部を設ける
Keep more than 10 emboss blanks both at front and end of the taping.
4. 機械的強度と取扱方法/Mechanical strength and treatment
1) カバ--プの剥離強度は 0.19 N 0.69 N とする。
Exfoliation strength of the cover tape should be 0.19 N
0.69 N.
2) テ-プ曲げ強度/Tape bending strength
テ-プを半 15 mm で曲げてもテ-プの変がないこと。
Tape should not be deformed by bending with a radius of 15 mm
2004-11-02 2008-04-21
Established Revised
Panasonic Semiconductor Opto Devices Co., Ltd.
テ-プ送り方向/Tape feeding direction
キャリアテ-プ/Carrier tape
カバ-テ-プ/Cover tape
10
°
F
引き出し方向
Pulling direction
リーダー部
Leader
空部(初め)
Blank (start)
チップ装着
Chip mounting part
空部(終わり)
Blank (end)
Min. 40 mm
Min. 200 mm
Min. 40 mm
送り穴側
Pin-feed hole side
実装部
/
Mountin
g
art
製品挿入図
Outline
極性指示図
Polarity mark
ラベル
Internal use label
Sheet 15/20
製品規格/Product Specification
テ-ピング仕/Taping Specification
品種名/Type NumberLNJ123W8PRZ
松下統一品番/Matsushita Unified Parts Number
LNJ123W8PRZ
3) 製品封入不良率/Percentage defective of enclosed
逆方向封入、表裏逆封入は 0 /リ-ルとする。
部品の欠落は、-ルの総部品数(表示数) 0.1 %、または 1 のいずれ、大きい方以下とし連続した
品抜けはいものとするただし、総数は変わらないものする
The product which was enclosed in reverse direction or with back side up should be counted as
0 piece/reel.
The number of dropped parts should be 0.1 % of entire number of parts or 1 piece, whichever larger.
There should be no continuous dropping however total number has to remain intact.
4)
テ-プ継ぎ目はないこと。/There should be no tape joint.
5. 梱包形態/Packing form
1)
リ-ル 4 000 個入りを基本とします。/A reel of 4 000 LED’s is a basic unit.
2)
リ-とシリカゲル共にアルミミネート袋包装を行います。
A reel and silica gel are put into an aluminum lamination bag.
2004-11-02 2008-04-21
Established Revised
Panasonic Semiconductor Opto Devices Co., Ltd.
※リール、パッキン(中箱,外箱)の端数対応可とする
Fractional packing, I,e, tape
reel and inner or outer carton, can be happened.
パッキングケ-ス(中箱)
Packing case (Inner)
※パッキングケース(中箱・外箱)内のラン混載可
Rank can be mixed within a packing (inner box and outer box).
パッキングケ-ス
(外箱)
Packing case (Outer)
リール/Reel
リール包装/Reel packing
アルミラミネート袋包
Aluminum lamination bag packing
アルミラミネート袋
A
luminum lamination bag
※リル内のランク混載不可
Rank can not be mixed within a reel.
シリカゲル/Silica gel
ラベル
Internal use label
ラベル
Internal use label
ラベル
/ Internal use label

LNJ123W8PRZ

Mfr. #:
Manufacturer:
Panasonic
Description:
LED GREEN/RED SMD/RIGHT ANGLE
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet