OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AT24C08N-10SI-1.8

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24
4
AT24C01A/02/04/08/16
0180R–SEEPR–4/04
Note: 1. This parameter is characterized and is not 100% tested.
Note: 1. V
IL
min and V
IH
max are reference only and are not tested.
Pin Capacitance
(1)
Applicable over recommended operating range from T
A
= 25°C, f = 1.0 MHz, V
CC
= +1.8V.
Symbol Test Condition Max Units Conditions
C
I/O
Input/Output Capacitance (SDA) 8 pF V
I/O
= 0V
C
IN
Input Capacitance (A
0
, A
1
, A
2
, SCL) 6 pF V
IN
= 0V
DC Characteristics
Applicable over recommended operating range from: T
AI
= -40°C to +85°C, V
CC
= +1.8V to +5.5V, T
AE
= -40°C to +125°C,
V
CC
= +1.8V to +5.5V (unless otherwise noted).
Symbol Parameter Test Condition Min Typ Max Units
V
CC1
Supply Voltage 1.8 5.5 V
V
CC2
Supply Voltage 2.5 5.5 V
V
CC3
Supply Voltage 2.7 5.5 V
V
CC4
Supply Voltage 4.5 5.5 V
I
CC
Supply Current V
CC
= 5.0V READ at 100 kHz 0.4 1.0 mA
I
CC
Supply Current V
CC
= 5.0V WRITE at 100 kHz 2.0 3.0 mA
I
SB1
Standby Current V
CC
= 1.8V V
IN
= V
CC
or V
SS
0.6 3.0 µA
I
SB2
Standby Current V
CC
= 2.5V V
IN
= V
CC
or V
SS
1.4 4.0 µA
I
SB3
Standby Current V
CC
= 2.7V V
IN
= V
CC
or V
SS
1.6 4.0 µA
I
SB4
Standby Current V
CC
= 5.0V V
IN
= V
CC
or V
SS
8.0 18.0 µA
I
LI
Input Leakage Current V
IN
= V
CC
or V
SS
0.10 3.0 µA
I
LO
Output Leakage Current V
OUT
= V
CC
or V
SS
0.05 3.0 µA
V
IL
Input Low Level
(1)
-0.6 V
CC
x 0.3 V
V
IH
Input High Level
(1)
V
CC
x 0.7 V
CC
+ 0.5 V
V
OL2
Output Low Level V
CC
= 3.0V I
OL
= 2.1 mA 0.4 V
V
OL1
Output Low Level V
CC
= 1.8V I
OL
= 0.15 mA 0.2 V
5
AT24C01A/02/04/08/16
0180R–SEEPR–4/04
Note: 1. The 24C01A/02/04 bearing the process letter “D” on the package (the mark is located in the lower right corner on the top
side of the package), guarantees 400 kHz (2.5 – 5.0V).
2. This parameter is characterized and is not 100% tested.
AC Characteristics
Applicable over recommended operating range from T
AI
= -40°C to +85°C, V
CC
= +1.8V to +5.5V, T
AE
= -40°C to +125°C,
V
CC
= +2.7V to +5.5V, CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol Parameter
1.8-volt 2.5, 2.7, 5.0-volt
UnitsMin Max Min Max
f
SCL
Clock Frequency, SCL 100 400
(1)
kHz
t
LOW
Clock Pulse Width Low 4.7 1.2 µs
t
HIGH
Clock Pulse Width High 4.0 0.6 µs
t
I
Noise Suppression Time
(2)
100 50 ns
t
AA
Clock Low to Data Out Valid 0.1 4.5 0.1 0.9 µs
t
BUF
Time the bus must be free before
a new transmission can start
(2)
4.7 1.2 µs
t
HD.STA
Start Hold Time 4.0 0.6 µs
t
SU.STA
Start Setup Time 4.7 0.6 µs
t
HD.DAT
Data In Hold Time 0 0 µs
t
SU.DAT
Data In Setup Time 200 100 ns
t
R
Inputs Rise Time
(2)
1.0 0.3 µs
t
F
Inputs Fall Time
(2)
300 300 ns
t
SU.STO
Stop Setup Time 4.7 0.6 µs
t
DH
Data Out Hold Time 100 50 ns
t
WR
Write Cycle Time 5 5 ms
Endurance
(1)
5.0V, 25°C, Byte Mode 1M 1M
Write
Cycles
6
AT24C01A/02/04/08/16
0180R–SEEPR–4/04
Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter-
nal device. Data on the SDA pin may change only during SCL low time periods (refer to
Data Validity timing diagram). Data changes during SCL high periods will indicate a start
or stop condition as defined below.
START CONDITION: A high-to-low transition of SDA with SCL high is a start condition
which must precede any other command (refer to Start and Stop Definition timing
diagram).
STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition.
After a read sequence, the stop command will place the EEPROM in a standby power
mode (refer to Start and Stop Definition timing diagram).
ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has
received each word. This happens during the ninth clock cycle.
STANDBY MODE: The AT24C01A/02/04/08/16 features a low-power standby mode
which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the
completion of any internal operations.
MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-
wire part can be reset by following these steps:
1. Clock up to 9 cycles.
2. Look for SDA high in each cycle while SCL is high.
3. Create a start condition.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24

AT24C08N-10SI-1.8

Mfr. #:
Buy AT24C08N-10SI-1.8
Manufacturer:
Description:
IC EEPROM 8K I2C 400KHZ 8SOIC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet