Enhanced Product ADuM3210-EP/ADuM3211-EP
Rev. A | Page 5 of 12
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3.3 V, 125°C OPERATION
All typical specifications are at T
A
= 25°C, V
DD1
= 5 V, V
DD2
= 3.3 V. Minimum/maximum specifications apply over the entire recommended
operation range: 4.5 V ≤ V
DD1
≤ 5.5 V, 3.0 V ≤ V
DD2
≤ 3.6 V, and −55°C ≤ T
A
≤ +125°C, unless otherwise noted. Switching specifications
are tested with C
L
= 15 pF and CMOS signal levels, unless otherwise noted.
Table 7.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
SWITCHING SPECIFICATIONS
Data Rate 25 Mbps Within PWD limit
Propagation Delay t
PHL
, t
PLH
15 55 ns 50% input to 50% output
Pulse Width Distortion PWD 3 ns |t
PLH
− t
PHL
|
Change vs. Temperature 5 ps/°C
Pulse Width PW 40 ns Within PWD limit
Propagation Delay Skew t
PSK
22 ns Between any two units
Channel Matching
Codirectional t
PSKCD
3 ns
PSKOD
Output Rise/Fall Time t
R
/t
F
3.0 ns 10% to 90%
Table 8.
Parameter Symbol
1 Mbps 10 Mbps 25 Mbps
Unit Min Typ Max Min Typ Max Min Typ Max
SUPPLY CURRENT
ADuM3210-EP I
DD1
1.3 1.7 3.5 4.8 7.6 9.9 mA
I
DD2
0.7 1.0 1.3 1.9 2.4 3.4 mA
ADuM3211-EP I
DD1
1.1 1.5 2.9 4.0 6.4 8.7 mA
I
DD2
0.8 1.6 1.9 2.5 3.7 5.0 mA
Table 9. For All Models
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
DC SPECIFICATIONS
Logic High Input Threshold V
IH
0.7 V
DDx
V
Logic Low Input Threshold V
IL
0.3 V
DDx
V
Logic High Output Voltages
OH
DDx
DDx
Ox
Ix
IxH
V
DDx
− 0.5 V
DDx
− 0.2 V I
Ox
= −3.2 mA, V
Ix
= V
IxH
Logic Low Output Voltages V
OL
0.0 0.1 V I
Ox
= 20 µA, V
Ix
= V
IxL
0.2 0.4 V I
Ox
= 3.2 mA, V
Ix
= V
IxL
Input Current per Channel I
I
−10 +0.01 +10 µA 0 V ≤ V
Ix
≤ V
DDx
Supply Current per Channel
Quiescent Input Supply Current I
DDI(Q)
0.4 0.8 mA
Quiescent Output Supply Current I
DDO(Q)
0.3 0.5 mA
Dynamic Input Supply Current I
DDI(D)
0.19 mA/Mbps
Dynamic Output Supply Current I
DDO(D)
0.03 mA/Mbps
AC SPECIFICATIONS
Common-Mode Transient Immunity
1
|CM| 25 35 kV/µs V
Ix
= V
DDx
, V
CM
= 1000 V,
transient magnitude = 800 V
Refresh Rate f
r
1.2 Mbps
1
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining V
O
> 0.8 V
DD
. The common-mode voltage slew rates apply to both
rising and falling common-mode voltage edges.