Data Sheet ADF4113HV
Rev. B | Page 13 of 20
Function Latch Map
DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
P2 P1 0 0 0 0 CP3 CP2 CP1 0 0 0 0 0 0 F4 F3 M3 M2 M1 F2 F1 C2(1) C1(0)
CONTROL
BITS
CP THREE-
STATE
PD
POLARITY
PRE-
SCALER
VALUE RESERVED
CURRENT
SETTING RESERVED
MUXOUT
CONTROL
POWER
DOWN
COUNTER
RESET
P2 P1 PRESCALER VALUE
0 0 8/9
0 1 16/17
1 0 32/33
1 1 64/65
I
CP
(µA)
CPI3 CPI2 CPI1
4.7kΩ
0 0 0 80
1 1 1 640
F4
CHARGE PUMP
OUTPUT
0 NORMAL
1 THREE-STATE
F3
PHASE DETECTOR
POLARITY
1 POSITIVE
0 NEGATIVE
M3 M2 M1 OUTPUT
0 0 0 THREE-STATE OUTPUT
0 0 1 DIGITAL LOCK DETECT
(ACTIVE HIGH)
0 1 0 N DIVIDER OUTPUT
0 1 1 DV
DD
1 0 0 R DIVIDER OUTPUT
1 0 1 ANALOG LOCK DETECT
1 1 0 SERIAL DATA OUTPUT
1 1 1 DGND
PD1 OPERATION
0 NORMAL
1 POWER DOWN
F1
COUNTER
OPERATION
0 NORMAL
1
R, A, B COUNTERS
HELD IN RESET
06223-022
Figure 22. Function Latch Map
FUNCTION LATCH
The on-chip function latch is programmed with C2 and C1 set
to 1,0, respectively. Figure 22 shows the input data format for
programming the function latch.
Counter Reset
DB2 (F1) is the counter reset bit. When DB2 is 1, the R counter
and the AB counters are reset. For normal operation, this bit
should be 0. Upon powering up, the F1 bit must be disabled,
and the N counter resumes counting in close alignment with
the R counter. (The maximum error is one prescaler cycle.)
Power-Down
DB3 (F2) in the function latch provides a software power-down
for the ADF4113HV. The device powers down immediately
after latching a 1 into Bit F2.
When the CE pin is low, the device immediately powers down
regardless of the state of the power-down bit (F2).
When a power-down is activated (either through software or
a CE pin activated power-down), the following events occur:
• All active dc current paths are removed.
• The R, N, and timeout counters are forced to their load
state conditions.
• The charge pump is forced into three-state mode.
• The digital clock detect circuitry is reset.
• The RF
IN
A and RF
IN
B inputs are debiased.
• The reference input buffer circuitry is disabled.
• The input register remains active and capable of loading
and latching data.
MUXOUT Control
The on-chip multiplexer is controlled by M3, M2, and M1 on
the ADF4113HV. Figure 22 shows the truth table.
Charge Pump Currents
CPI3, CPI2, and CPI1 program the current setting for the
charge pump. The truth table is given in Figure 22.
Prescaler Value
P2 and P1 in the function latch set the prescaler values. The
prescaler value should be chosen so that the prescaler output
frequency is always less than or equal to 200 MHz. Thus, with
an RF frequency of 2 GHz, a prescaler value of 16/17 is valid,
but a value of 8/9 is not.
PD Polarity
This bit sets the phase detector polarity bit. See Figure 22.
CP Three-State
This bit controls the CP output pin. With the bit set high, the
CP output is put into three-state. With the bit set low, the CP
output is enabled.