OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

1583527-1

P1-P3P4-P6P7-P9P10-P12P13-P15
409- 10039
“Micro” Pneumatic Tooling Assembly 1490567- 1
Rev C 13 of 15Tyco Electronics Corporation
3. Remove the stop ring by inserting the end of a flat blade screwdriver under the removal notch and
prying outward. Slide the stop ring off the front of the air cylinder.
Be careful when removing parts to prevent scarring on the outside surface of the cylinder.
4. Slide the locking collar off the front of the air cylinder .
5. Inspect the stop ring groove for wear or permanent deformation. If excessive wear or damage is
evident, refer to Paragraph 9.3 for information on obtaining customer repair service.
B. Installation
1. Using a caliper, measure the width of the stop ring groove. See Figure 8. Using this dimension, refer
to Figure 9 for the proper stop ring to be used.
2. Slide the locking collar onto the front of the air cylinder.
3. Slide the stop ring onto the front of the air cylinder and carefully seat the ring into the stop ring
groove. Do not deform the ring.
4. Install the friction ring.
5. Visually inspect the tooling assembly to assure that the locking collar, stop ring, and friction ring are
installed properly.
6. Using a caliper, measure the diameter of the stop ring. See Figure 8. Take measurements at several
different locations around the ring. If the measurements are within the tolerance (for the stop ring being
used) provided in Figure 9, the tooling assembly is considered dimensionally correct. If any of the
measurements are not within the tolerance, refer to Paragraph 9.3 for information on obtaining further
evaluation and repair.
Figure 8
Diameter of
Stop Ring
Width of Stop
Ring Groove
9.3. Repair
For customer repair service, please contact a Tyco Electronics Representative at 1--800--526--5136.
10. REVISION SUMM ARY
Revisions to this customer manual include:
S Added “Original Instructions” to page 1
CAUTION
!
409- 10039
“Micro” Pneumatic Tooling Assembly 1490567- 1
Rev C14 of 15 Tyco Electronics Corporation
1
2
3
4
Type 3 Valve Uses Kit 1583089--1
5
Part Number is
Stamped on Valve
REPLACEMENT PARTS FOR HAND ACTUATED POWER UNIT 1490567--1 (Non--Logic)
ITEM PART NUMBER DESCRIPTION QTY PER UNIT
1 1583088--2 VALVE ASSEMBLY, Pneumatic 1
2 189848--1 COLLAR, Locking 1
3 38111 HOSE, Air 1
4 904384--1
RING, Stop— Groove Width 1.73 [.068] Approx
Ring Diameter 50.5 [1.99] Max
1
Not Shown
217434--1G
REPAIR KIT, Seals (O--rings and snap rings for power unit) 1
5
1583089--1G
REPAIR KIT, Spool (Seals, Spoolcap and Spring for Valve
Body)
1
Figure 9
G Recommended Spare Part
409- 10039
“Micro” Pneumatic Tooling Assembly 1490567- 1
Rev C 15 of 15Tyco Electronics Corporation
1
2
3
4
5
6
7
8
9
10
12
13
14
15
16
17
18
11
REPLACEMENT PARTS FOR TOOL HO LDER ASSEMBLY
QTY PER TOOL HOLDER
ASSEMBLY
ITEM PART NUMBER DESCRIPTION
1673611--1
(Short Holder)
356304--1
(Straight Action
Holder)
1
1673602--1 CAM, Short Logic 1 -- --
1
356623--1 CAM, Straight Action -- -- 1
2 356439--1 ECCENTRIC 1 1
3 356440--2 INSERT, 626 Ratchet 1 -- --
4 356441--1 PAWL 1 1
5
354425--1G
PIN, Pivot 2 4
6 3--21028--5 PIN, Slotted Spring, .09 X 438 2 -- --
7 4--21028--4 PIN, Slotted Spring .09 X X 1.00 2 -- --
8 4--21028--9 PIN, Slotted Spring, .125 X 375 1 1
9 356437--1 PLA TE, Eccentric Adjustment 1 1
1
0
1--2100--5 SCREW,SocketHdCap,4--40X.50 4 -- --
1
0
1--2100--4 SCREW,SocketHdCap,4--40X.38 -- -- 4
11 21055--4 WASHER, Flat, Regular , Number 4 3 3
12
189765--1G
SETSCREW, Special 1 1
13 37887 SPRING 1 1
1
4
-- -- TOOL HOLDER, Small 1 -- --
1
4
356624--1 TOOL HOLDER, Straight Action -- -- -- --
15
356022--1G
SLEEVE, Safety 1 -- --
16 1--21003--3 SCREW, Flat Socket Hd Cap, 4--40 X .25 -- -- 1
17 1--21003--4 SCREW, Flat Socket Hd Cap, 4--40 X .38 -- -- 2
18 1673691--1 GUIDE PLATE, Straight Action Tool Holder -- -- 1
G Recommended Spare Part
Figure 10
P1-P3P4-P6P7-P9P10-P12P13-P15

1583527-1

Mfr. #:
Buy 1583527-1
Manufacturer:
TE Connectivity
Description:
CCII SA ADAPTER-6-26 & MICRO
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet