OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

GP2AP002S00F

P1-P3P4-P6P7-P9P10-P12
GP2AP002S00F
4
Sheet No.: OP13009EN
■Absolute Maximum Ratings
Ta=25°C (unless otherwise specified)
Parameter
Symbol
Rating
Unit
Remarks
Supply voltage
Vcc
-0.3 to 3.8
V
LED supply voltage
V
LED
-0.3 to 3.8
V
LED peak forward current
I
LED
300
mA
Logic I/O supply voltage
Vio
-0.3 to Vcc+0.3 and
3.8V or less
V
Cf: Refer to the page 7, Directions for
power-line connection
SDA/SCL pull-up voltage
-
Vio-0.3 to Vio+0.3 and
3.8V or less
V
Cf: Refer to the page 7, Directions for
power-line connection
Operating temperature
Topr
-25 to +85
°C
Storage temperature
Tstg
-40 to +85
°C
Soldering temperature
Tsol
260
°C
peak temperature duration:10sec
■Recommended Operating Conditions
Ta=25°C (unless otherwise specified)
Parameter
Symbol
Operating condition
Unit
Remarks
Supply voltage
Vcc
2.4 to 3.6
V
LED supply voltage
V
LED
2.4 to 3.6
V
Operating temperature
T
opr
-25 to 85
°C
Logic I/O supply voltage
Vio
1.65 to Vcc
V
SCL, SDA input low level
VIL
-0.3 to 0.2×Vio
V
SCL, SDA input high level
VIH
0.8×Vio to Vio+0.3
V
■Electrical and Optical Characteristics
Ta=25°C ,Vcc=3.3V, V
LED
=3.3V R
LED
=6.8Ω (unless otherwise specified)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remarks
Current consumption
operating mode
I
CC
-
240
600
uA
No detection object, Ev=0 lx.
*1, except for LED and driver
shutdown mode
I
CC-S
-
-
1.0
No input signal.
*1, except for LED and driver
LED peak current
I
LED
-
170
-
mA
Peak emission wavelength
λ
p
-
940
-
nm
Vout terminal High level output voltage
V
OH
Vio-0.5
Vio-0.3
Vio+0.3
V
I
OH
=0.3mA,*2
Vout terminal Low level output voltage
V
OL
-
-
0.5
V
I
OL
=1mA, *2
Response time (H→L)
tp
HL
-
-
50
ms
*2
Response time (L→H)
tp
LH
-
-
50
ms
Rise time
tr
-
1
-
μs
*2, CL=15pF
Fall time
tf
-
1
-
μs
Maximum detection distance
Lon
25
65
-
mm
*3, Detection object:
KODAK Gray Card (r = 0.18)
Operation mode B1
Minimum no detection distance
Loff
-
78
150
mm
Wake up time
t
sdw
-
-
100
ms
*4
Maximum acceptable illuminance
Ev
3000
-
-
lx
*5
SCL clock frequency
SCL
4
-
400
kHz
*1. Current consumption through VLED terminal (including LED and its driver output) depends on
actual environment and situations. (See attached document【1】1-1)
GP2AP002S00F
5
Sheet No.: OP13009EN
d
KODAK
Gray Card
GP2AP002S00F
*2. Parameters defined for Vout output waveform specifications
*3. Detection distance
tp
LH
tf
tr
90%
50%
10%
VOH
VOL
Without detection object
tp
HL
With detection object
State of the object
to be detected
Vout output
(at normal output mode)
1
0
GP2AP002S00F output example vs. distance characteristics (operation mode B1)
180
200
0
Distance, d (mm)
100
120
140
160
20
40
60
80
Maximum Detection Distance
Mimimum No Detection Distance
VO value
detection→
←no detection
GP2AP002S00F
6
Sheet No.: OP13009EN
*4. Wake up time, tsdw, is defined as a delay of the 1st LED emission after issuing the I
2
C write command to release
GP2AP002S00F from the shutdown mode. Note that there should be no external light noise sources in this
particular examination. Also, by definition, it does not matter where reflective object is, but it is recommended
that the object should be placed at d << Lon because VO is initialized to 0 and the next expected change is 0 to 1.
*5. Test set-up for “Maximum Acceptable Illuminance” measurement
Illuminance should be measured and evaluated at Emitter/Detector surface of GP2AP002S00F.
The maximum acceptable illuminance, Ev, is a maximum level of illuminance at which GP2AP002S00F
should keep its sensing result, VO, as "0" (no detection) as long as no reflective objects exist. However,
GP2AP002S00F may start to exhibit false detection with external light noise beyond this level.
See attached document【1】1-10 for more details.
■Supplement
●This product is built-in photodiode.
●Compliance with each regulation
1) The RoHS directive(2002/95/EC)
This product complies with the RoHS directive(2002/95/EC) .
Object substances: mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls(PBB)
and polybrominated diphenyl ethers(PBDE)
2) Content of six substances specified in Management Methods for Control of Pollution Caused by Electronic
Information Electronic Information Products Regulation (Chinese : 电子信息产品污染控制管理办法).
Category
Toxic and hazardous substances
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr
6+
)
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
Proximity sensor
✓
✓
✓
✓
✓
✓
✓: indicates that the content of the toxic and hazardous substance in all the homogeneous materials of the part is
below the concentration limit requirement as described in SJ/T 11363-2006 standard .
●This product shall not contain the following materials.
Also, the following materials shall not be used in the production process for this product.
Materials for ODS : CFCs, Halon, Carbon tetrachloride, 1,1,1-Trichloroethane (Methylchloroform)
●Brominated flame retardants
Specific brominated flame retardants such as the PBB and PBDE are not used in this device at all.
●Product mass : Approx . 0.017 g
●Country of origin : China
●Packing : Refer to the attached sheet, Page 11.
●Moisture level: MSL3
Light source A
GP2AP002S00F
Emitter/Detector surface
P1-P3P4-P6P7-P9P10-P12

GP2AP002S00F

Mfr. #:
Buy GP2AP002S00F
Manufacturer:
Sharp Microelectronics
Description:
Proximity Sensors Prox Snsr 3.8V 940nm w/ Amb Light Sensor
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet