Functional description of the SPI L9953LXP
28/35 Doc ID 16185 Rev 3
Table 19. SPI - input data and status registers 1
Bit
Input register 1 (write) Status register 1 (read)
Name Comment Name Comment
23 Enable bit
If enable bit is set the device
will be switched in active
mode. If enable bit is cleared
device goes into standby mode
and all bits are cleared. After
power-on reset device starts in
standby mode.
Always 1
A broken VCC or SPI
connection of the
L9953LXP can be
detected by the
microcontroller, because
all 24 bits low or high is
not a valid frame.
22
OUT8 OC
recovery
enable
In case of an over-current
event the over-current status
bit (status register 0) is set and
the output is switched off. If the
over-current recovery enable
bit is set the output will be
automatically reactivated after
a delay time resulting in a
PWM modulated current with a
programmable duty cycle (bit
21 of input data register 0).
Depending on occurrence of
over-current event and internal
clock phase it is possible that
one recovery cycle is executed
even if this bit is set to zero.
VS overvoltage
In case of an overvoltage
or under voltage event
the corresponding bit is
set and the outputs are
deactivated. If Vs voltage
recovers to normal
operating conditions
outputs are reactivated
automatically.
21 0 / 1 VS undervoltage
20
OUT7 OC
recovery
enable
Thermal shutdown
In case of a thermal
shutdown all outputs are
switched off. The
microcontroller has to
clear the TSD bit by
setting the reset bit to
reactivate the outputs.
19
OUT6 OC
recovery
enable
Temperature
warning
The TW bit can be used
for thermal management
by the microcontroller to
avoid a thermal
shutdown. The
microcontroller has to
clear the TW bit.
18 0 / 1 Not ready bit
After switching the
device from standby
mode to active mode an
internal timer is started to
allow charge pump to
settle before the outputs
can be activated. This bit
is only present during
start up time
Since this bit is
controlled by internal
clock it can be used for
synchronizing testing
events(e.g. measuring
filter times).
L9953LXP Functional description of the SPI
Doc ID 16185 Rev 3 29/35
17
Enable high
R
DSon
OUT7
After 50ms the bit can be
cleared. If over-current
condition still exists, a wrong
load can be assumed.
OUT8 – HS
open-load
The open-load detection
monitors the load current
in each activated output
stage. If the load current
is below the open-load
detection threshold for at
least 1 ms (t
dOL
) the
corresponding open-load
bit is set. Due to
mechanical/electrical
inertia of typical loads a
short activation of the
outputs (e.g. 3ms) can
be used to test the open-
load status without
changing the
mechanical/electrical
state of the loads.
16
OUT5 OC
recovery
enable
0
15
OUT4 OC
recovery
enable
OUT7 – HS
open-load
14
OUT3 OC
recovery
enable
OUT6 – HS
open-load
13
OUT2 OC
recovery
enable
0
12
OUT1 OC
recovery
enable
0
11
OUT8 PWM1
enable
If the PWM1/2 enable bit is set
and the output is enabled
(input register 0) the output is
switched On if PWM1/2 input is
high and switched off if
PWM1/2 input is low. OUT7 is
controlled by PWM2 input. All
other outputs are controlled by
PWM1 input.
0
10 0 / 1
OUT5 – HS
open-load
9
OUT7 PWM2
enable
OUT5 – LS
open-load
8
OUT6 PWM1
enable
OUT4 – HS
open-load
7
OUT4 – LS
open-load
6
Enable high
R
DSon
OUT6
OUT3 – HS
open-load
5
OUT5 PWM1
enable
OUT3 – LS
open-load
4
OUT4 PWM1
enable
OUT2 –HS
open-load
3
OUT3 PWM1
enable
OUT2– LS
open-load
2
OUT2 PWM1
enable
OUT1 – HS
open-load
1
OUT1 PWM1
enable
OUT1 – LS
open-load
0 1 No error bit
A logical NOR-
combination of all bits 1
to 22 in both status
registers.
Table 19. SPI - input data and status registers 1 (continued)
Bit
Input register 1 (write) Status register 1 (read)
Name Comment Name Comment
Packages thermal data L9953LXP
30/35 Doc ID 16185 Rev 3
5 Packages thermal data
Figure 10. Packages thermal data

L9953LXPTR

Mfr. #:
Manufacturer:
STMicroelectronics
Description:
IC DVR DOOR ACTUATOR POWERSSO36
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet