204Pin DDR3 1.35V 1600 SO-DIMM
4GB Based on 512Mx8
AQD-SD3L4GN16-MG
IDD Specification parameters Definition( IDD values are for full operating range of Voltage and Temperature)
4GB, 512Mx64 Module(1 Rank x8)
Operating One bank Active-Precharge current; tCK = tCK(IDD), tRC =
tRC(IDD), tRAS = tRASmin(IDD); CKE is HIGH, /CS is HIGH between valid
commands;Address bus inputs are SWITCHING; Data bus inputs are
SWITCHING
Operating One bank Active-read-Precharge current; IOUT = 0mA; BL =
8, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRC = tRC (IDD), tRAS = tRASmin(IDD),
tRCD = tRCD(IDD); CKE is HIGH, /CS is HIGH between valid commands;
Address bus inputs are SWITCHING; Data pattern is same as IDD4W
Precharge power-down current; All banks idle; tCK = tCK(IDD); CKE is
LOW; Other control and address bus inputs are STABLE; Data bus inputs are
FLOATING
Precharge quiet standby current; All banks idle; tCK = tCK(IDD); CKE is
HIGH, /CS is HIGH; Other control and address bus inputs are STABLE; Data bus
inputs are FLOATING
Precharge standby current; All banks idle; tCK = tCK(IDD); CKE is HIGH,
/CS is HIGH; Other control and address bus inputs are SWITCHING; Data bus
inputs are SWITCHING
Active power - down current; All banks open; tCK = tCK(IDD); CKE is LOW;
Other control and address bus inputs are STABLE; Data bus inputs are FLOATING
Active standby current; All banks open; tCK = tCK(IDD), tRAS =
tRASmax(IDD), tRP = tRP(IDD); CKE is HIGH, /CS is HIGH between valid
commands; Other control and address bus inputs are SWITCHING; Data bus
inputs are SWITCHING
Operating burst read current; All banks open, Continuous burst reads, IOUT
= 0mA; BL = 4, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD),
tRP = tRP(IDD); CKE is HIGH, /CS is HIGH between valid commands; Address
bus inputs are SWITCHING; Data pattern is same as IDD4W
Operating burst write current; All banks open, Continuous burst writes; BL =
8, CL = CL(IDD), AL = 0; tCK = tCK(IDD), tRAS = tRASmax(IDD), tRP = tRP(IDD);
CKE is HIGH, /CS is HIGH between valid commands; Address bus inputs are
SWITCHING; Data bus inputs are SWITCHING IDD4R
Burst refresh current; tCK = tCK(IDD); Refresh command at every tRFC(IDD)
interval; CKE is HIGH, /CS is HIGH between valid commands; Other control and
address bus inputs are SWITCHING; Data bus inputs are SWITCHING
Self refresh current; CK and /CK at 0V; CKE ≒ 0.2V; Other control and
address bus inputs are FLOATING; Data bus inputs are FLOATING
Self refresh temperature current
(SRT-enabled): MAX TC = 95°C
Operating bank interleave read current; All bank interleaving reads, IOUT
= 0mA; BL = 8, CL = CL(IDD), AL = tRCD(IDD)-1*tCK(IDD); tCK = tCK(IDD), Trc =
tRC(IDD), tRRD = tRRD(IDD), tRCD = 1*tCK(IDD); CKE is HIGH, CS is HIGH
between valid commands;Address bus inputs are STABLE during DESELECTs;
Data pattern is same as IDD4R;
1. Module IDD was calculated on the specific brand DRAM(4xnm) component IDD and can be differently
measured according to DQ loading capacitor.
