OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

PI3VDP411LSAZBEX

P1-P3P4-P6P7-P9P10-P12P13-P13
7
www.pericom.com PS9059A 07/28/12
PI3VDP411L SA
Dual Mode DisplayPort™ to DVI/HDMI™ Electrical bridge (Level Shier)
Absolute Maximum Ratings (Over operating free-air temperature range)
Item Rating
Supply Voltage to Ground Potential 5.5V
All Inputs and Outputs
-0.5V to V
DD
+0.5V
Ambient Operating Temperature -40 to +85°C
Storage Temperature -65 to +150°C
Junction Temperature 150°C
Soldering Temperature 260°C
Stress beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
Electrical Characteristics
Table: Power Supplies and Temperature Range
Symbol Parameter Min Typ Max Units Comments
V
DD
3.3V Power supply 3.0 3.3 3.6 V
I
CC
Max Current 100 mA
I
CC_squelch
Supply Current when no
TMDS clock present
8 mA
I
CCQ
Standby Current 2 mA OE# = HIGH
T
CASE
Case temperature range
for operation with spec.
-40 85 Celsius (°)
8
www.pericom.com PS9059A 07/28/12
PI3VDP411L SA
Dual Mode DisplayPort™ to DVI/HDMI™ Electrical bridge (Level Shier)
Table: Dierential Input Characteristics forIN_Dx signals
Symbol Parameter Min Typ Max Units Comments
T
bit
UI, Unit Interval 360 ps
T
bit
is determined by the display mode. Nominal
bit rate ranges from 250Mbps to 2.5Gbps per lane.
Nominal Tbit at 2.5 Gbps = 400 ps. 360ps = 400ps-
10%
V
RX_DIFF
Input Dierential Volt-
age Level
0.175 1.200 V See note 1 below
T
RX_EYE
Minimum Eye Width at
IN_D input pair
0.8 Tbit
V
CM-ACp-p
AC Peak Common
Mode Input Voltage
100 mV See note 2 below
Z
RX_DC
40 50 60 Ω
Required IN_D+ as well as IN_D- DC impedance
(50 ±20% tolerance).
Z
RX-Bias
0 2.0 V
Intended to limit power-up stress on chipset's PCIE
output buers.
Z
RX_HIGH-Z
100 k Ω
Dierential inputs must be in a high impedance
state when OE# is HIGH.
1. V
RX-DIFF
= 2x|V
RX-D- -
V
RX-D-
| Applies to IN_Dx signals
2. V
CM-AC-p-p
= |V
RX-D
- - V
RX-D
-|/2 - V
RX-CM-DC
V
RX-CM-DC
= DC(avg) of |V
RX-D+
+ V
RX-D
-|/2
V
CM-AC-p-p
includes all frequencies above 30 kHz.
TMDS Outputs
e level shier's TMDS outputs are required to meet HDMI 1.3 specications.
e HDMI 1.3 Specication is assumed to be the correct reference in instances where this document conicts with the HDMI 1.3
specication.
9
www.pericom.com PS9059A 07/28/12
PI3VDP411L SA
Dual Mode DisplayPort™ to DVI/HDMI™ Electrical bridge (Level Shier)
Table 2: Dierential Output Characteristics for TMDS_OUT signals
Symbol Parameter Min Typ Max Units Comments
V
H
Single-ended high
level output voltage
V
DD
-10mV V
DD
V
DD
+10mV
V
V
DD
is the DC termination voltage
in the HDMI or DVI Sink. V
DD
is
nominally 3.3V
V
L
Single-ended low level
output voltage
V
DD
-600mV V
DD
-50 0mV V
DD
-400mV
V
e open-drain output pulls down
from V
DD
.
V
SWING
Single ended output
swing voltage
425 500 600 mV
Swing down from TMDS termina-
tion voltage (3.3V ±10%)
I
OFF
Single-ended current
in high-Z state
50 µA
Measured with TMDS outputs
pulled up to V
DD
Max _(3.6V)
through 50Ω resistors.
T
SKEW-INTRA
Intra-pair dierential
skew
30 ps
is dierential skew budget is in
addition to the skew presented be-
tween D+ and D- paired input pins.
HDMI revision 1.3 source allowable
intrapair skew is 0.15 T
bit
.
T
SKEW-INTER
Inter-pair lane-to-lane
output skew
100 ps
is lane-to-lane skew budget is in
addition to skew between dieren-
tial input pairs
T
JIT
Jitter added to TMDS
signals
25 ps
Jitter budget for TMDS signals as
they pass through the level shier.
25ps = 0.056 at 2.25 Gbps
TMDS output oscillation elimination
e inputs already incorporate a squelch circuit. erefore, nothing is needed from application standpoint to eliminate TMDS output
oscillation when there is no TMDS input present. e IC will do this automatically.
Table 3: HPD Characteristics
Symbol Parameter Min Typ Max Units Comments
V
IH-HPD
Input High Level 2.0 5.0 5.3 V
Low-speed input changes state on cable plug/
unplug
V
IL-HPD
HPD_SINK Input Low
Level
0 0.8 V
I
IN-HPD
HPD_SINK Input Leakage
Current
70 µA
Measured with HPD_SINK at V
IH-HPD
max
and V
IL-HPD
min
V
OH-HPD
HPD_source Output
High-Level
2.5
V
DD
V
V
DD
= 3.3V ±10%
I
OH
= -4mA(MIN) / -8mA(MAX)
V
OL-HPD
HPD_source Output Low-
Level
0 0.4 V
I
OL
= 4mA(MIN) / 8mA(MAX)
T
HPD
HPD_SINK to HPD_
source propagation delay
200 ns
Time from HPD_SINK changing state to
HPD_source changing state. Includes HPD_
source rise/fall time
T
RF-HPDB
HPD_source rise/ fall time 1 20 ns
Time required to transition from V
OH- HPDB
to V
OL-HPDB
or from V
OL-HPDB
to V
OH-HPDB
P1-P3P4-P6P7-P9P10-P12P13-P13

PI3VDP411LSAZBEX

Mfr. #:
Buy PI3VDP411LSAZBEX
Manufacturer:
Diodes Incorporated
Description:
Video ICs Dual Mde DisplayPort TMDS Electricl brdge
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet