OMO ElectronicOMO Electronic
Expand menu
0 Cart

1416716

P1-P3P4-P6P7-P8
FOC-M12-MNNA-TC...
4 / 8 PHOENIX CONTACT 103995_en_02
5 Dimensions
5.1 Dimensional drawing
Figure 1 Dimensions (in mm)
5.2 Drilling diagram
Figure 2 Drilling diagram (in mm)
6 Pin assignment
Figure 3 View of the component side
7 Notes
Mounting
The FO transceiver, connectors, and couplings should only
be mounted finger tight.
Achievable transmission paths
FOC-M12-MNNA-TC-1300 is designed for 50/125 m fi-
bers. The maximum achievable transmission paths are
2500m.
FOC-M12-MNNA-TC-650 is designed for 980/1000 m fi-
bers. The maximum achievable transmission paths are
75m.
To optimize transmission performance and to achieve the
maximum transmission path, correctly pre-assembled fiber
optic connectors are required.
13,5
M16x1,5
7
3
22
Ø25
12xØ0,48
3x□1
5
M12x1
23
19
120°
Ø1,6
5x1,778
5,65
11,3
Ø0,8
0,889
Ø23
Pin Name Function
1 RD+ Receive Data Out+
2 RD- Receive Data Out-
3 SD Signal Detect
4 RxVcc +3.3 V Receiver
5 RxGnd GND Receiver
6 SDA I
2
C Serial Data IO
7 Sclk I
2
C Serial Clock Input
8 TD- Transmit Data In-
9 TD+ Transmit Data In+
10 TxDis Disable Transmitter Input
11 TxGnd GND Transmitter
12 TxVcc +3.3 V Transmitter
1
2
3
4
5
6
7
8
9
10
11
12
FOC-M12-MNNA-TC...
103995_en_02 PHOENIX CONTACT 5 / 8
8 External wiring
Figure 4 External wiring
Ferrites (La):
Typical impedance: 120 at 100 MHz
Maximum DC resistance: 0.15 at 200 mA
NOTE: To optimize the function of the transceiv-
er, a decoupling of the supply voltage and a cable
termination is required as shown in Figure 4.
NOTE: The decoupling capacitors and termina-
tion resistors should be as close as possible to
the inputs of the transceiver or the LVPECL re-
ceiver.
11 TX GND
9 DIN +
8 DIN -
12 TX Vcc
5 RX GND
2 DOUT -
1 DOUT +
4 RX Vcc
Transceiver
100nF1μF
82Ω82Ω
130Ω130Ω
Vcc = 3,3V
LVPECL
Receiver
LVPECL
Driver
Vcc = 3,3V
82Ω82Ω
130Ω130Ω
100nF
1μF
La
La
FOC-M12-MNNA-TC...
6 / 8 PHOENIX CONTACT 103995_en_02
9 Block diagram
Figure 5 Block diagram
10 I
2
C interface
10.1 I
2
C addresses
PRE-AMP
POST-AMP
Quantizer
Management
LED
Driver
1
2
3
5
4
6
7
10
12
11
9
8
RD+
RD-
SD
RxGnd
RxVcc
SDA
SCLK
TxDisable
TxVcc
TxGnd
TD+
TD-
Serial address = A0 (hex)
Address (hex) Field size (byte) Name Description
00-5F 96 Serial ID GP NVRAM; R/W under valid OEM password
60-7F 32 Vendor Specific Vendor-specific EEPROM
80-FF 128 Reserved Reserved for future use
Serial address = A2 (hex)
Address (hex) Field size (byte) Name Description
00-27 40 Alarm and Warning
Threshold
High/low limits for warnings and alarms
28-37 16 Reserved Reserved – do not write; reads undefined
38-5B 36 Calibration Constants Numerical constants for external calibration
5C-5E 3 Reserved Reserved – do not write; reads undefined
5F 1 Checksum GP NVRAM; R/W under valid OEM password
60-69 10 Analog Data Real-time analog parameter data
6A-6D 4 Reserved Reserved – do not write; reads undefined
6E 1 Control/Status Bits Control and status bits
6F 1 Reserved Reserved – do not write; reads undefined
70-71 2 Alarm Flags Alarm status bits; read only
72-73 2 Reserved Reserved – do not write; reads undefined
74-75 2 Warning Flags Warning status bits; read only
P1-P3P4-P6P7-P8

1416716

Mfr. #:
Buy 1416716
Manufacturer:
Phoenix Contact
Description:
Fiber Optic Connectors M12 duplex 650nm for POF and PCF-MM
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet