HTCM-SCE-TP-1/2-6H-9 Datasheet HTCM-SCE-TP-1/2-6H-9, HTCM-SCE-TP-1/4-4H-4, HTCM-SCE-TP-1/2-4H-9 | P4-P6

RW-2524 Issue 4

Page 4 of 15

Feb’ 2015

RW-2524 Issue 4

*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks

of their respective owners.

If this document is printed it becomes uncontrolled.

¼ inch 4-Hole Cable Marker

Figure 4: HTCM-SCE-TP-1/4-4H

½ inch 6-Hole Cable Marker

Figure 5: HTCM-SCE-TP-1/2-6H

RW-2524 Issue 4

Page 5 of 15

Feb’ 2015

RW-2524 Issue 4

*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks

of their respective owners.

If this document is printed it becomes uncontrolled.

2.3

Test Requirements

The test requirements shall be as specified in Table 2.

QUALITY ASSURANCE PROVISIONS

3.1.

Qualification Tests

Qualification tests are those performed on finished Cable Marker, continuous sheet or material pellets

submitted for qualification as a satisfactory product and shall consist of all tests listed in this

specification.

Some tests require un-perforated lengths which are not supported by the finished Cable marker

format therefore continuous sheet shall be tested. For this document, ‘Cable Marker’ shall be defined

as specimen that represents the finished article; this is the material taken from the end of the

production line. ‘Continuous strip’ is specimen taken from work in progress and is removed from the

production line prior to finishing. Other than the format, both of these specimens are identical.

3.2.

Acceptance Tests

Acceptance tests are those performed on markers submitted for acceptance under contract.

Acceptance tests shall consist of the following: Dimensions, Heat shock and Mark Adherence

performance

3.3.

Qualification Test Samples

Qualification test samples shall consist of 5m (16 foot) of continuous strip, and at least 500 cable

markers and 1kg of material pellets.

Cable Marker, Continuous Strip and Material pellets shall be taken from the same compound batch.

Unless otherwise specified, the Cable Markers shall be removed from the carrier for testing. Where

required by test method limitations, testing shall be done on marker material

RW-2524 Issue 4

Page 6 of 15

Feb’ 2015

RW-2524 Issue 4

*Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks

of their respective owners.

If this document is printed it becomes uncontrolled.

TEST METHODS

4.1

Preparation of Test Specimens

Finished Cable Markers for testing shall be printed with TE approved printers and ribbons (TE

document 411-121005) and printed with Arial size 10 pt font. The initial print contrast must be C8 or

above, reference TE Document 411-121002.

Unless otherwise specified, tests shall be carried out on Cable Markers that have had no pre-

conditioning. When required by the test method, testing shall be made with continuous strip. Unless

otherwise specified, all tests shall be made under standard ambient conditions according to IEC

Publication 60212. In cases of dispute the tests shall be carried out at a temperature of 23±2°C and

at 50±5% relative humidity.

4.2

Print Performance

4.2.1

Mark Adherence

Three Cable Markers shall be prepared as detailed in Clause 4.1 and tested in accordance with TE

test reference 109-121012. Samples shall be tested using a Crockmeter fitted with an eraser and 1kg

load using the number of rubs specified in the requirement table.

After the Mark Adherence test, marking shall be examined for legibility using normal reading vision.

Print contrast shall be measured in accordance with TE Document 411-121002.

4.2.2.

Solvent Resistance

Nine Cable Markers shall be prepared as detailed in Clause 4.1 and tested in accordance with TE test

reference 109-121014.

The marking shall be examined for legibility using normal reading vision. Print contrast shall be

measured in accordance with TE Document 411-121002.

4.2.3.

Fluid Resistance

Three Cable Markers as prepared as in Clause 4.1 shall be completely immersed in each of the fluids

for the times and at the temperatures specified in the requirements table. The volume of the fluid shall

not be less than 20 times that of the specimen. After immersion, the markers are lightly blotted with

tissue paper to remove excess surface fluid and air dried at 23 ± 2°C for 45 ± 15min. The print shall

be tested in accordance with TE test reference 109-121012. Samples are tested with a Crockmeter

fitted with ‘Super Twill’ cloth and a 1kg load.

After the print permanence test, marking shall be examined for legibility using normal reading vision.

Print contrast shall be measured in accordance with TE Document 411-121002.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15

HTCM-SCE-TP-1/2-6H-9

Mfr. #:

Buy HTCM-SCE-TP-1/2-6H-9

Manufacturer:

Raychem / TE Connectivity

Description:

Wire Labels & Markers HTCM-SCE-TP-1/2-6H-9

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

HTCM-SCE-TP-1/2-6H-9

HTCM-SCE-TP-1/2-6H-9

Products related to this Datasheet